Integra DTR-40.2, Инструкция по эксплуатации

Страница: 51 / 104

51
En
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “
Full Band ” for speakers that can output low fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies. If you set up your speak-
ers using Audyssey MultEQ Room Correction and
Speaker Setup, please make sure manually that any THX
speakers are set to “
80Hz(THX) ” crossover.
■
Subwoofer

Yes :
Select if a subwoofer is connected.

No :
Select if no subwoofer is connected.
■
Front

Full Band

40Hz , 45Hz , 50Hz , 55Hz , 60Hz , 70Hz , 80Hz(THX)
to 130Hz , 150Hz , 200Hz
Note
• If the “ Subwoofer ” setting is set to “ No ”, the “ Front ” setting is
fixed at “ Full Band ”.
■
Center *1 , Surround *1 , Surr Back *2*3*4*5

Full Band

40Hz , 45Hz , 50Hz , 55Hz , 60Hz , 70Hz , 80Hz(THX)
to 130Hz , 150Hz , 200Hz

None :
Select if no speaker is connected.
■
Front Wide *1*2*4*6 , Front High *1*2*4*5

Full Band

40Hz , 45Hz , 50Hz , 55Hz , 60Hz , 70Hz , 80Hz(THX)
to 130Hz , 150Hz , 200Hz

None :
Select if no speaker is connected.
Note
*1 “ Full Band ” can be selected only when “ Full Band ” is
selected in the “ Front ” setting.
*2 If the “ Surround ” setting is set to “ None ”, this setting cannot
be selected.
*3
If the “ Surround ” setting is set to anything other than “ Full
Band ”, “ Full Band ” cannot be selected here.
*4 If the “ Speakers Type(Front) ” setting is set to “ Bi-Amp ”
(
➔
50 ), this setting cannot be selected.
*5 If the Powered Zone 2 is being used (
➔
77 ), this setting can-
not be selected.
*6 If the “ Powered Zone 2 ” setting is set to
“ Act ”
(
➔
77 ), this
setting cannot be selected.
■
Surr Back Ch

1ch :
Select if only one surround back speaker is con-
nected.

2ch :
Select if two (left and right) surround back speakers
are connected.
Note
• If the “ Surr Back ” setting is set to “ None ” (
➔
51 ), this setting
cannot be selected.
■
LPF of LFE
(Low-Pass Filter for the LFE Channel)

80Hz , 90Hz , 100Hz , 110Hz , 120Hz
With this setting, you can specify the cutoff frequency
of the LFE channel’s low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only
applies to sources that use the LFE channel.
■
Double Bass
With the Double Bass function, you can boost bass out-
put by feeding bass sounds from the front left, right, and
center channels to the subwoofer.

On :
Double Bass function on.

Off(THX) :
Double Bass function off.
Note
• This function can be set only if the “ Subwoofer ” setting is set to
“ Yes ”, and the “ Front ” setting is set to “ Full Band ”.
• If you’re using THX-certified speakers, select “ Off(THX) ”.
This setting is set automatically by Audyssey MultEQ ®
Room Correction and Speaker Setup function (
➔
28 ).
This setting is NOT set automatically by
Audyssey MultEQ Room Correction and Speaker Setup
function (
➔
28 ).