Customer Services (858) 578-7887 & (888) GO IN
TEC
IN
TEC
Controls, 12700 Stowe Dr., Suite 1
0
0, Poway, CA 92064
Fax (858) 578-4633 & (888) FX IN
TEC
www.inteccontrols.com
Specification subject to change without notice.
Printed in USA 130917
Polygard® is a registered trademark of MSR
DGC3
PolyGard
®
Digital Gas Controller
User Manual - DGC3
Page 22
4 Notes and General Information
It is important to read this user manual carefully in order to understand the information and instructions. The
PolyGard
®
DGC3 gas monitoring, control and alarm system may only be used for applications in accordance to the
intended use. The appropriate operating and maintenance instructions and recommendations must be followed.
Due to permanent product developments, MSR reserves the right to change specifications without notice. The
information contained herein is based on data considered to be accurate. However, no guarantee or warranty is
expressed or implied concerning the accuracy of these data.
4.1
Intended Product Application
The PolyGard
®
DGC3 is designed and manufactured for controlling, for saving energy and keeping OSHA air
quality in commercial buildings and manufacturing plants (i.e. detection and automatic exhaust fan control for
automotive maintenance facilities, enclosed parking garages, engine repair shops, warehouses with forklifts, fire
stations, tunnels, etc.).
4.2
Installers’ Responsibilities
It is the installer’s responsibility to ensure that all PolyGard
®
DGC3 are installed in compliance with all national and
local regulations and OSHA requirements. All installations should be executed only by technicians familiar with
proper installation techniques, the codes, standards and proper safety procedures for control installations, as well
as the latest edition of the National Electrical Code (ANSI/NFPA70). It is also essential to strictly follow all
instructions as provided in this user manual.
4.3 Maintenance
It is recommended to check the PolyGard
®
DGC3 system regularly. With regular maintenance deviancies in
efficiency can easily be corrected.
4.4
Limited Warranty
MSR-Electronic-GmbH and IN
TEC
Controls warrants the PolyGard
®
DGC3 for a period of two years from the date
of shipment against defects in material or workmanship. Should any evidence of defects in material or workmanship
occur during the warranty period, IN
TEC
Controls will repair or replace the product at their own discretion, without
charge.
This warranty does not apply to units that have been altered, had attempted repair, or been subject to abuse,
accidental or otherwise. The above warranty is in lieu of all other express warranties, obligations or liabilities.
This warranty applies only to the PolyGard
®
DGC3. MSR-Electronic-GmbH and/or IN
TEC
Controls shall not be
liable for any incidental or consequential damages arising out of or related to the use of the PolyGard
®
DGC3.
If the PolyGard
®
DGC3 needs to be returned to IN
TEC
Controls for service, an RMA number must be obtained prior
to sending.
Specifications subject to change without notice. | USA 130917 | Page 22 of 22
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN
TEC
| relevantsolutions.com/inteccontrols
DGC3 – UserManual
Polygard® is a registered trademark of MSR | DGC3
Specifications subject to change without notice. | USA 160104 | Page 22 of 22
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN
TEC
| relevantsolutions.com/inteccontrols
DGC3 – UserManual
PolyGard
®
is a registered trademark of MSR-Electronic GmbH | DGC3
INTEC Controls | 12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.INTEC | inteccontrols.com
Specifications subject to change without notice. | USA 200211 | Page 22 of 22
DGC3 – UserManual
