manualshive.com logo in svg

INSTEON SwitchLinc 2476ST, Руководство пользователя

Поделиться
Скачать
INSTEON SwitchLinc 2476ST Скачать руководство пользователя страница 3

SwitchLinc Timer Owner’s Manual  

 

Page 3 of 23 

 

ABOUT SWITCHLINC TIMER 

SwitchLinc Timer presents you with an elegant and stylish way to control a wired-in light in your home at 
the touch of a button. Its internal timer counts down 15 minutes (or an hour for each subsequent tap of 
the paddle top) to turn itself off automatically. Send commands from a Controller to activate the load and 
its programmed timer. Or use SwitchLinc to remotely control other INSTEON devices.   
  

 

Status LED & 

brightness indicator 

Trim frame 

Wallplate  

(sold separately) 

Set button (push) 

Air gap (pull) 

Paddle bottom 

(Off/Dim) 

Paddle top  

(On/Bright) 

 

 

 

 

 

 

Key SwitchLinc Timer Features 

•

  Once installed, setup is easy – Links to other INSTEON devices in minutes 

•

  Controls standard, wired-in incandescent lighting and inductive loads up to 480 Watts, 15 Amps  

•

 

Local timer can be set for 15 minutes and increased in increments of one hour

 

•

  Responds to and controls other INSTEON devices as well as X10 devices  

•

  Indicates INSTEON setup mode activity and operational states with a Status LED  

•

  LED bar shows provides a gentle nightlight when the load is off  

•

  Paddle and trim frame colors are changeable to almond, black, brown, gray, ivory, light almond, or 

white with optional kits  

•

  White LED bar color is changeable to amber, blue, green, red, or frosted white with optional kits  

•

  Stores setup state in memory so settings aren’t lost during power outages 

•

  Wires into standard J-boxes (requires a NEUTRAL connection) 

•

  Supports “virtual” 3-, 4-, or more-way circuits with multiple SwitchLincs  

•

 

Two-year warranty 

 

What is Included with SwitchLinc Timer 

•

  SwitchLinc Timer – INSTEON Countdown Wall Switch Timer (Non-Dimming)  

•

  2 x Mounting screws 

•

  3 x Wire nuts   

•

 

Quick-Start Guide 

 

Содержание SwitchLinc 2476ST
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды