manualshive.com logo in svg

INSTEON 2486DWH6, Руководство пользователя

Поделиться
Скачать
INSTEON 2486DWH6 Скачать руководство пользователя страница 8

INSTEON KeypadLinc Dimmer User’s Guide 

 

Page 8 of 39 

 

 Installing KeypadLinc Dimmer 
1.  For best INSTEON Network performance, be sure you have properly installed at least two Access 

Point Modules. 

2.  At the circuit breaker or fuse panel, disconnect the power for 

all

 of the circuits in the switch junction 

box.  Verify that power is off by trying to turn on the lights controlled by the switches. 

3.  Remove the faceplate from the switch junction box, and then unscrew the switch you are replacing 

and pull it out from the junction box. 

4.  Disconnect the wires from the switch you are replacing.  If the wires cannot be detached by 

unscrewing them, cut the wires where they enter the switch, then strip ½” of insulation off the ends. 

5.  If you are installing KeypadLinc Dimmer into a standard 

two-way circuit

 (where only one switch 

controls the load), follow the diagram below to identify and connect the LINE, LOAD, NEUTRAL, and 
GROUND wires.  If the colors of the wires do not match the diagram, be sure you have identified the 
wires correctly before connecting them. 

6.  If you are installing KeypadLinc Dimmer into a 

multi-way circuit

 (where more than one switch 

controls the same load), follow the instructions in the section titled 

Installing KeypadLinc Dimmer in a 

Multi-Way Circuit

 to identify and connect the LINE, TRAVELER, NEUTRAL, and GROUND wires. 

7.  After you have connected all of the wires, ensure that all of the wire connectors are firmly attached 

and that there is no exposed copper except for the GROUND wire. 

8.  Orient KeypadLinc Dimmer with the SET button on bottom, gently place it into the junction box, and 

then screw it into place. 

9.  Turn the circuit breaker back on or re-install the fuse. 

10.  After the SET button illuminates, verify KeypadLinc Dimmer is working properly by turning the light on 

and off. 

11.  Reinstall the trim plate. 

NOTE 

The NEUTRAL wire will not 
normally be connected to the 
switch you are replacing.  If there is 
no NEUTRAL wire in the junction 
box, please consult an electrician 
or call 
 

SmartHome Tech Support 

800-SMARTHOME

 

Main Panel 

120 VAC 

LINE 

Usually Black 

LOAD 

Usually Red, Blue or Black

NEUTRAL 

Usually White 

GROUND

Bare Copper

LINE 

Black 

NEUTRAL 
White 

GROUND 

Bare Copper 

LOAD 
Red

Light 

Fixture(s)

Содержание 2486DWH6








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды