manualshive.com logo in svg

INSTEON 2486DWH6, Руководство пользователя

Поделиться
Скачать
INSTEON 2486DWH6 Скачать руководство пользователя страница 6

INSTEON KeypadLinc Dimmer User’s Guide 

 

Page 6 of 39 

 

Preparing to Install KeypadLinc Dimmer 

 

Prior to installing KeypadLinc Dimmer, please review the entire installation procedure, and take the 
following precautions: 

•

  Be sure that you have turned off the circuit breaker or removed the fuse for the circuit you are 

installing KeypadLinc Dimmer in.  Installing KeypadLinc Dimmer with the power on will expose you to 
dangerous voltages. 

•

  KeypadLinc Dimmer requires a small amount of power to operate, which it receives from a connection 

to the NEUTRAL electrical wire (usually white).  If you are replacing a standard mechanical switch 
with KeypadLinc Dimmer, the switch you are replacing will normally 

not

 have a connection to the 

neutral wire.  However, most junction boxes will contain a NEUTRAL wire that you can connect 
KeypadLinc Dimmer to.  If your junction box does not contain a neutral wire, please call Smarthome 
Tech Support at 800-SMARTHOME (800-762-7846), or consult an electrician. 

•

  Don’t use KeypadLinc Dimmer to control low-voltage lighting, fluorescent lights, or motors.  These are 

inductive loads, which KeypadLinc Dimmer is not designed to control.  Use a Smarthome SwitchLinc 
Relay instead. 

•

  Don’t use KeypadLinc Dimmer to control an electrical outlet, because non-dimmable or inductive 

loads may be plugged into it. 

•

  KeypadLinc Dimmer may feel warm during operation.  The amount of heat generated is within 

approved limits and poses no hazards.  To minimize heat buildup, ensure that the area surrounding 
the rear of KeypadLinc Dimmer has adequate ventilation by clearing away excess insulation. 

IMPORTANT! 

If you are not knowledgeable about and comfortable with electrical circuitry, you should have a 
qualified electrician install KeypadLinc Dimmer for you.  If you have any questions, please consult an 
electrician or call  

Smarthome Tech Support 

800-SMARTHOME 

(800-762-7846) 

Содержание 2486DWH6








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды