Inspur i24 Скачать руководство пользователя страница 32

Страница: 32 / 37

Inspur proprietary and confidential information

Network Port PXE

5.1.1

Network Port PXE

Table 5- 1 Network Port PXE

Item

Content

Objective

To verify that LOM ports on the server support PXE.

Prerequisites

The server is powered on.

The Dynamic Host Configuration Protocol (DHCP) server

is configured properly.

The installation server is configured properly

The DHCP server and installation server are connected to

NIC1 on the server over the network.

Procedure

Power on the server and wait until it starts.

Press F12 on the first BIOS screen.

Expected result

The server starts over PXE.

An IP address is obtained for the server.

The server starts to install an OS over the network.

Description

None

Note:

(1)

Before acceptance, the system should be properly installed, and the software and

hardware debugging should pass, and the system can run normally.

(2)

The acceptance project should be confirmed by relevant personnel of both Inspur

and the user.

(3)

During the acceptance and preliminary inspection tests, the personnel of both parties

shall perform strict tests against relevant standards. Some index parameters have been

Содержание i24






































Результаты поиска

Содержание i24

Отзывы:

Похожие инструкции для i24

Бренды по названию

Популярные бренды

Inspur i24, Руководство по приемке сервера

Результаты поиска

Содержание i24

Отзывы:

Похожие инструкции для i24

Бренды по названию

Популярные бренды