Inovance EtherCAT MD800 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 78

Inovance EtherCAT MD800 Скачать руководство пользователя страница 7

6

INOVANCE TECHNOLOGY EUROPE GmbH
MD800 EtherCAT Starting Guide_EN_v1.1_20211109.docx

4.1

HARDWARE LAYOUT

Figure 1 -SI-ECAT card terminal distribution

The SI-ECAT card uses a standard Ethernet RJ45 socket, which is connected to the EtherCAT master station, and
its pin signal definition is the same as that of the standard Ethernet

The pins of the network are the same, cross-wire and straight-wire are both possible.

SI-ECAT card terminal function description:

Terminal

symbol

Terminal name

Description

EC IN

Input port

After installation, EC IN is on the left and EC OUT is on
the right when facing to the RJ45 interface. The two
interfaces must be connected correctly.
The Cat5e shielded twisted pair (STP) network cable
must be used for ensuring stability.
To improve the anti

‑

interference capability of

communication, it is recommended to install it in the
expansion card slot 2.

EC OUT

Output port

SI-ECAT card indicator description:

Indicator light

Status description

Approach

RUN/ERR

The green light is

always on

The communication is

normal

None

The red light is

always on

SI-ECAT card and

node communication

timeout

Check the connector to see if there is
interference.

Red light flashes

slowly

SI-ECAT card and

rectifier

communication

timeout

1. Check whether the communication card
is installed correctly.
2. Check whether the rectifier module is
normal.

Red light flashes

quickly

SI-ECAT card failure

Check malfunction according to the FAULT
code of the rectifier display panel.

«
...
5
6
7
8
9
...
»

Содержание EtherCAT MD800















































































Отзывы:

Нет отзывов