Innova OnLine 10K Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 57

Innova OnLine 10K Скачать руководство пользователя страница 24

21

Note

：

：

：

：

●

: Lightened constantly

△

: #1-#4 Lightened circularly

★

: Flashing

↑

: Depended on the fault/warning status or other status

Table 5-3 Alarm definition

UPS condition

Buzzer status

Fault active

Continuous

Warning active

Beep every second

Battery output

Beep every 4 seconds

Bypass output

Beep every 2 minutes

The UPS provides useful information about UPS itself, load status,
events, measurements, identification, and settings through the front
panel display.
During powering on, the LCD would display the Welcome logo for
several seconds and then enter to the default page which shows the
UPS status summary.
The  display  automatically  returns  to  the  default  UPS  status
summary screen when no button has been pressed for 15 minutes.
On  the  UPS  status  summary  screen  it  provides  the  following
information:

Status summary, including mode and load

Notice or alarm status, if any are present

Battery status, including status and charge level

«
...
22
23
24
25
26
...
»

Содержание OnLine 10K


























































Отзывы:

Нет отзывов