Ingersoll-Rand Trane Intellipak Скачать руководство пользователя страница 8

8

 RT-SVB98B-EN

Screen shown only for units with Energy Recovery Installed 

  Exhaust Air Bypass Damper Control Gain 

 

  Rate Time 

XXX  Sec  

                                └─┬─┘

 

Range 0.0-100.0 

 

Default 0 

 

 

One of the following two screens will be shown: 

    Only if Energy Recovery Installed and value is greater than 0. 

    

Range 1-255 and Disable 

 

Default 3 Min 

 

   ┌─┴─┐

 

  Energy Wheel Off Delay Time:  

XXX Min 

 

  Turn Wheel Off When Temp Above Setpoint   

 
“Disable” is displayed when the value is incremented above 255.  A selection of “Disable”  disables wheel shutoff 
changes to screen below and allows continuous wheel operation when conditions permit. 

Only if Energy Recovery Installed and value is equal to Disable. 

  Energy Wheel Off Delay Time:    Disable   
  Wheel Remains On Until Call For Cooling   

 

Screen shown only on units with Rapid Restart or Dehumidification installed 
 

 

Range 15 - 50 

 

Default 30 

 

                                  ┌─┴─┐

 

 

Rapid DX Interstage Timing:      XXX Sec 

 

 

 

 

Screen shown if in this submenu 

   

 

  End Of Submenu (NEXT) To Enter SETUP 

 

 

Содержание Trane Intellipak











Отзывы: