Ingersoll-Rand HP935 Скачать руководство пользователя страница 28

Страница: 28 / 61

OPERATING INSTRUCTIONS

HP935, VHP750, MHP825, XHP750, XP1060

Wedge Diagnostic Display Codes

If the

fault indicator lamp is illuminated, refer to the

Alert/Shutdown list below.

If the

fault indicator lamp is illuminated, refer to the

Engine diagnostic list below.

ALERT/SHUTDOWN CONDITIONS

ALERT

SHUTDOWN

CODE

LIGHT

BLINKS

CODE

LIGHT

STEADY

DELAY

(sec)

Engine Speed < Min. RPM

CPRSR

Malfunction.

Engine Speed > Max. RPM

CPRSR

Malfunction.

Engine Crank Time Exceeded

CPRSR

Malfunction.

*Engine Oil Temperature
> 252 deg. F

CPRSR

Malfunction.

*Intake Manifold Temperature
>180 deg. F

CPRSR

Malfunction.

*Water In Fuel – CUMMINS

CPRSR

Malfunction.

Engine Not Responding To
Throttle command

CPRSR

Malfunction.

Too Many Crank Attempts
During Autostart

CPRSR

Malfunction.

Engine Shut Itself Down:
reason unknown

CPRSR

Malfunction.

Low AE Oil Pressure

CPRSR

Malfunction.

Disch. Temp (RT2)
Sensor Fault

CPRSR

Malfunction.

Sep. Tank Pressure (PT1)
Sensor Fault

CPRSR

Malfunction.

Seperator Tank Pressure >20
PSI During Start Attempt
(Engine Will Not Crank)

CPRSR

Malfunction.

Machine Over Pressure

CPRSR

Malfunction.

Safety Valve Open

CPRSR

Malfunction.

*CAN derived data

Содержание HP935






























































Результаты поиска

Содержание HP935

Отзывы:

Похожие инструкции для HP935

Бренды по названию

Популярные бренды

Ingersoll-Rand HP935, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание HP935

Отзывы:

Похожие инструкции для HP935

Бренды по названию

Популярные бренды