Ingersoll-Rand HP935 Скачать руководство пользователя страница 14

Страница: 14 / 61

ANSI SYMBOLS

HP935, VHP750, MHP825, XHP750, XP1060

Improper operation of this equipment.
Can cause serious injury or death.
Read Operator’s Manual supplied with

this

machine before operation or

servicing.

Modification or alteration of this machine.
Can cause serious injury or death.
Do not alter or modify this machine
without the express written consent of

the

manufacturer.

Collapsing jackstand.
Can cause serious injury.

Insert locking pin completely.

km/h

Excessive towing speed.
Can cause serious injury or
death.
Do NOT exceed 65 mph
(105 km/hr.)

Do not operate without
guard in place.

Rotating fan blade.

Can cause serious
injury.

Access lifting bail from
inside machine.

Falling off machine.

Can cause serious injury
or death.

Door under pressure.

Can cause serious injury.

Use both hands to open door
when machine is running.

When using air tools
attach safety device (OSHA
Valve) at source of air supply for each
tool.

Disconnected air hoses whip.

Can cause serious
injury or death.

Combustible gas.

Can cause serious
burns, blindness or
death.

Keep sparks and open
flames away from
batteries.

DO NOT WELD.

ELECTRONIC DAMAGE
WILL OCCUR.

This engine is equipped with an
electronic engine controller and
other electronic components.

WARNING

CAUTION

Содержание HP935






























































Результаты поиска

Содержание HP935

Отзывы:

Похожие инструкции для HP935

Бренды по названию

Популярные бренды

Ingersoll-Rand HP935, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание HP935

Отзывы:

Похожие инструкции для HP935

Бренды по названию

Популярные бренды