background image

  

Book 43212455 (11/03)   

 

 

11

SECTION 2 - WARRANTY 

 

 

Ingersoll-Rand, through its distributors, warrants to the initial user that each portable air compressor 
manufactured by it, will be free of defects in material and workmanship for a period of the earlier of twelve 
(12) months from shipment to or the accumulation of 2,000 hours of service by the initial user. 

 
Portable compressor airends will be free of defects in material and workmanship for a period of the earlier 
of twenty four months from shipment to or the accumulation of 4,000 hours of service by the initial user.  
The warranty against defects will include replacement of the complete airend, provided the original airend 
is returned assembled and unopened. 
 
Portable Compressor Airend Limited Optional Warranty - The earlier of sixty (60) months from shipment to 
or the accumulation of 10,000 hours of service.  The optional warranty is limited to defects in rotors, 
housings, bearings and gears and provided all the following conditions are met: 

1.  The original air end is returned assembled and unopened. 
2.  Continued use of genuine Ingersoll-Rand parts, fluids, oil and filters. 
3.  Maintenance is performed at prescribed intervals. 

Oil-Free airends are fee-based and may require a maintenance agreement.  Formal enrollment is 
required. 
 
Ingersoll-Rand will provide a new part or repaired part, at its election, in place of any part, which is found 
upon its inspection to be defective in material and workmanship during the period prescribed above. Such 
part will be repaired or replaced without charge to the initial user during normal working hours at the place 
of business of an Ingersoll-Rand distributor authorized to sell the type of equipment involved or other 
establishment authorized by Ingersoll-Rand.  User must present proof of purchase at the time of 
exercising warranty. 
  
The above warranty does not apply to failures occurring as a result of abuse; misuse, negligent repairs, 
corrosion, erosion and normal wear and tear, alterations or modifications made to the product without 
express written consent of Ingersoll-Rand; or failure to follow the recommended operating practices and 
maintenance procedures as provided in the product’s operating and maintenance publications. 
 
Accessories or equipment furnished by Ingersoll-Rand, but manufactured by others, including, but not 
limited to, engines, shall carry whatever warranty the manufacturers have conveyed to Ingersoll-Rand 
and which can be passed on to the initial user. 
 
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, (EXCEPT 
THAT OF TITLE),AND THERE ARE NO WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR 
A PARTICULAR PURPOSE.

Содержание HP600CMH













































Отзывы: