Ingenico iWL252 Скачать руководство пользователя

Страница: 110 / 116

SKYZER TECHNOLOGIES

PAGE 110 OF 116

NITRO INGENICO ICT250 AND IWL252 2015 PAYMARK SOFTWARE OPERATING GUIDE

Version 1.0

15.4 Battery Information

Your terminal is supplied with a removable, rechargeable battery. This battery

recharges when the terminal is connected to the charger unit.
Following installation, the battery charge status is indicated by the battery icon

found in the top right hand corner of the terminal display.
When you charge the battery for the first time, it should be charged until full

capacity is indicated. This may take from 4 to 16 hours.
New terminals are dispatched with some charge present. Transactions can be

performed providing the terminal is connected to the charger unit so that it

can continue charging.
One of these Battery Status Symbols will be displayed depending on the

charge in the battery and whether the handset is on the Base.

Battery low

Battery fully charged (off base)

If the battery symbol shows empty, and the terminal displays a “Battery Low”

warning then you should recharge the terminal battery as soon as possible for

a minimum of 6 hours.
DO NOT attempt to use your terminal without its battery pack.
DO NOT  attempt to open the battery pack. There are no user-serviceable

components.
DO NOT remove the battery pack from the terminal for extended periods of

time.
DO NOT discard old or broken battery packs. Return them to your terminal

supplier for correct recycling.
DO NOT leave on constant charge as this will have a degrading effect on the

batteries life span.

15.5 EXTERNAL POWER SUPPLY

•

Only an Ingenico approved power supply (CE Marked) specified for use

with this terminal must be used.

•

Operate only from a power source as specified on the Power Supply

Unit.

Содержание iWL252





















































































































Результаты поиска

Содержание iWL252

Отзывы:

Похожие инструкции для iWL252

Бренды по названию

Популярные бренды

Ingenico iWL252, Руководство по эксплуатации

Результаты поиска

Содержание iWL252

Отзывы:

Похожие инструкции для iWL252

Бренды по названию

Популярные бренды