INGENIA Nix series Скачать руководство пользователя страница 68

Страница: 68 / 124

Nix Product Manual |

Wiring and Connections

INGENIA | 01/22/2019

•

It is strongly recommended to use an external fuse to limit the maximum power dissipation according to the
chosen shunt resistor.

•

Wire section should be, at least, like the motor wires

• Shunt resistor connections should be as short as possible to reduce parasitic inductances.

Shunt resistor calculation tool

Additional information on shunt braking resistor sizing and a calculation tool can be found

here



Hot surfaces

Be careful, shunt resistor may have hot surfaces during operation.



Configuration of the shunt

The shunt transistor can be configured using parameters in the register

0x2103 - Shunt configuration

When the supply voltage reaches the maximum voltage indicated in register

0x2101 - Drive bus voltage

, the

shunt transistor is activated.

As a recommendation, set the DC bus voltage limit above the maximum expected DC supply v 5%.

When using batteries set the DC bus voltage limit below the maximum charge voltage.

This will allow

regenerative braking and protect the battery against overcharging.



Содержание Nix series





























































































































Результаты поиска

Содержание Nix series

Отзывы:

Похожие инструкции для Nix series

Бренды по названию

Популярные бренды

INGENIA Nix series, Руководство по эксплуатации продукта

Результаты поиска

Содержание Nix series

Отзывы:

Похожие инструкции для Nix series

Бренды по названию

Популярные бренды