Infortrend EonStor U16U-G4010 Скачать руководство пользователя страница 12

Страница: 12 / 108

EonStor U16U Installation and Hardware Reference Manual

- xii -

EonStor

U16U-G4010

This appendix lists all the technical specifications of the ES U16U RAID

subsystem.

♦

Appendix C: EonStor U16U Packaging

This appendix completely describes the ES U16U package that a user will receive.

♦

Appendix D: Accessories and Spare Parts

This appendix lists all the part numbers for the different accessories and spare parts

that are available for the ES U16U

♦

Appendix E: Pin Outs

This appendix shows the different pin outs of the ES U16U subsystem. Pin outs for

the SCSI host ports, RS-232C Audio Jack and the RJ-45 Ethernet connector are

among those specified.

Who should read this manual?

This manual assumes that its readers are experienced with computer hardware installation

and are familiar with storage enclosures.

Содержание EonStor U16U-G4010













































































































Результаты поиска

Содержание EonStor U16U-G4010

Отзывы:

Похожие инструкции для EonStor U16U-G4010

Бренды по названию

Популярные бренды

Infortrend EonStor U16U-G4010, Руководство по установке и аппаратным средствам

Результаты поиска

Содержание EonStor U16U-G4010

Отзывы:

Похожие инструкции для EonStor U16U-G4010

Бренды по названию

Популярные бренды