Infoblox IB-4010 Скачать руководство пользователя

Страница: 6 / 27

System Health LED

This LED identifies the overall health of the system.

Green = Normal
Amber = System is degraded
Red = System is in critical condition

Power On/ Standby
Button and Power LED

This LED indicates whether the power is on.

Green = System is on
Amber = System is in standby mode

Dark = System has no power supply

Disk Drives (all systems
use hot-swappable hard
disks)

The

uses four (4) hard disk drives configured in a RAID (Redundant Array of Independent Disks) 10

Infoblox-4010

array.
The

0 uses four (4) hard disk drives in a RAID 10 array.

Advanced Appliance PT-400

The

appliance uses four (4) hard disk drives in a RAID 6 array.

Trinzic Reporting TR-4000

The

uses eight (8) hard disk drives in a RAID-10 array.

Network Insight ND-4000

Drive LEDs

Each disk drive has one Fault/UID LED (green/amber) that indicates the connection of the disk drive, and a
circular Online/Activity LED (green) that goes around the Fault/UID LED to indicate read/write activity status of the
disk drive.

VGA Port

The VGA port is not supported. Use the console port or LAN1 port for initial setup.

Disk Drive Front Panel LEDs

Disk drives are located on the appliance front panel. To the right of each drive, two LEDs display connection and activity status.

lists the

Table 2

disk drive LED combinations and the states they represent.

Table 2 Disk Drive LED Combinations

Online/Activity LED (Green)

Fault/UID LED (Amber/Blue)

Description

Off or circulating green

Steady green

The drive is operating normally.

Off or circulating green

Steady amber

The drive has failed, or it has received a predictive failure alert.

Ethernet Port LEDs

View the Activity and Link LEDs to see link activity and connection speeds on Ethernet ports.

describes the status conveyed by Ethernet

Figure 3

port LEDs through their color and illumination (steady glow or blinking).

Figure 3 Ethernet Port LEDs

SFP/SFP+ Interface Support

The Infoblox 4000 Series appliances support optional interface configurations to accept SFP transceiver modules, for 1GbE optical and copper

Содержание IB-4010




























Результаты поиска

Содержание IB-4010

Отзывы:

Похожие инструкции для IB-4010

Бренды по названию

Популярные бренды

Infoblox IB-4010, Руководство по установке

Результаты поиска

Содержание IB-4010

Отзывы:

Похожие инструкции для IB-4010

Бренды по названию

Популярные бренды