manualshive.com logo in svg

Infinova V6822-T Series, Руководство пользователя, Страница: 24 / 61

Поделиться
Скачать
Infinova V6822-T Series Скачать руководство пользователя страница 24

20

Figure 4-7 

Click “Yes” button, run the program to finish the update. 

The response time is due to the program type. You may wait a long time for 

some program. Do not power off during the update process. Power-off will 

make update fail, even damage the original program or unable to update again. 

After update successfully, it needs to reboot the system. There is time prompt in 

the web page during reboot. After reboot, it will skip to new web page to run 

new program. 

Note:

 Available only for the super user. 

Factory Settings 

V6822-T series camera provides online reset function, which greatly facilitates 

reset adjustment.   

Select “Keep current IP unchanged”, click “Reset” button and the system will 

pop up a message as below: 

Figure 4-8 

Click “OK”, all the parameters (excluding IP address) will be reset to the 

factory default settings.   

If “Keep current IP unchanged” is unselected, the IP address will be reset to the 

Содержание V6822-T Series






























































Отзывы:

Нет отзывов