Infinity 6250LQ Скачать руководство пользователя страница 3

Страница: 3 / 44

FY operation manual

- 3 -

Chapter 1

SAFETY INFORMATION

1.1

Important Safety Information

Before using your INFINITY FY6250LQ InkJet Digital Printer, Please read following safety information. Pay
attention to the cautions on the Printer.

•

Don’t block the hole on the cover.

•

Don’t insert any object into the Printer groove. Don’t let any kind of moistures splash into Printer.

•

Only use the Power Supply according to the label. You may choose either AC 110V or 220V for
different countries and regions.

•

Please make sure the connection is correct for the Power Supply Cable before turning on the Printer

•

Avoid to use the Socket controlled by the switch on the wall or by auto timing controller

•

Please keep Printer away from the Magnet Interaction, For example: Speaker and Mobil-phone

•

Don’t use damaged Electrical Power wire

•

Don’t try to repair Printer by yourself

•

Contact your Local Service Center to repair, if the following situations occur:

Power wire or Socket damaged

Liquid splashes into Printer

Printer damaged and Cover broken

Printer can’t work properly or printing quality has conspicuous change

1.2

Caution When Using Printer

•

Don’t use your hand to move print head; otherwise the Printer will be damaged.

•

Always use power switch to Turn On/Off the Printer. Before Shutting down the Printer, do not pull
out Power Supply wire or Data Wire.

•

Before moving the Printer, please make sure the Print head at Original position and firmed.

1.3

Guidance When Using Ink Container

•

Keep ink container away from children. Don’t drink or touch.

•

If ink spills on the skin, please wash with soap and water. If ink splashes into eye, please wash with
water immediately

•

Don’t shake the ink container, which causes ink leak.

•

After three months, you should take off the ink container, clean it and dry it.

•

Please keep surrounding clean when you replace a new ink container. It helps you improve printing
quality.

1.4

Choosing Printer Installation Place

•

Make sure to leave enough space for the Printer; otherwise, the Printer may not work properly.

•

Don’t leave Printer at a place where temperature and humidity change severely. Avoid sunshine,
strong light and heat.

•

Avoid shaking and vibration.

•

Keep sufficient room for air circulation.

•

Place Printer nearby the Power socket, so it is easy to connect or disconnect the Power Supply

Содержание 6250LQ













































Результаты поиска

Содержание 6250LQ

Отзывы:

Похожие инструкции для 6250LQ

Бренды по названию

Популярные бренды

Infinity 6250LQ, Руководство по эксплуатации

Результаты поиска

Содержание 6250LQ

Отзывы:

Похожие инструкции для 6250LQ

Бренды по названию

Популярные бренды