Infinique IHR16-12F2I-S Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 58

Infinique IHR16-12F2I-S Скачать руководство пользователя страница 10

8

TEC-VS-219-1605-V01

3. DVR Connections

3.1 HDD Installation
Caution: Please do not take out hard drive when DVR is powered ON!

(1) Disconnect the power, and then remove screws on the sides and rear to open DVR upper cover.
(2) Connect the data and power connectors of the SATA cable to the main board. Install the HDD to fix
it on the bracket and then connect the installed SATA cable to HDD power and the data lines.
(3) Install the upper cover back carefully and put back the screws that were removed earlier.
Note: It is strongly recommended to use special hard drives designed for video surveillance
applications.

3.2 Camera and Monitor Connection

DVR video output signals are transmitted to a VGA monitor or HDMI monitor by VGA or HDMI cable.

3.3 Power Supply Connection

Please use the supplied power adapter to connect DVR. Before powering on, make sure the cables on the
audio and video I/O ports and network port are connected.

«
...
8
9
10
11
12
...
»

Содержание IHR16-12F2I-S



























































Отзывы:

Нет отзывов