Infineon XC886CLM Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 663

background image

XC886/888CLM

Memory Organization

User’s Manual

3-6

V1.3, 2010-02

Memory Organization, V 1.2

3.4

Memory Protection Strategy

The XC886/888 memory protection strategy includes:

•

Read-out protection: The user is able to protect the contents in the Flash (for Flash
devices) and ROM (for ROM devices) memory from being read.
– Flash protection is enabled by programming a valid password (8-bit non-zero

value) via BSL mode 6.

– ROM protection is fixed with the ROM mask and is always enabled.

•

Flash program and erase protection: This feature is available only for Flash devices.

3.4.1

Flash Memory Protection

As long as a valid password is available, all external access to the device, including the
Flash, will be blocked.

For additional security, the Flash hardware protection can be enabled to implement a
second layer of read-out protection, as well as to enable program and erase protection.

Flash hardware protection is available only for Flash devices and comes in two modes:

•

Mode 0: Only the P-Flash is protected; the D-Flash is unprotected.

•

Mode 1: Both the P-Flash and D-Flash are protected.

The selection of each protection mode and the restrictions imposed are summarized in

Table 3-1

Flash Protection Modes

Flash Protection Without hardware

protection

With hardware protection

Hardware
Protection Mode

-

0

1

Activation

Program a valid password via BSL mode 6

Selection

Bit 4 of password = 0 Bit 4 of password = 1

MSB of password = 0

Bit 4 of password = 1
MSB of password = 1

P-Flash
contents can be
read by

Read instructions in
any program memory

Read instructions in
the P-Flash

Read instructions in
the P-Flash or D-
Flash

External access
to P-Flash

Not possible

Not possible

Not possible

P-Flash program
and erase

Possible

Not possible

Not possible

*

«
...
51
52
53
54
55
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: Value Point Страницы: 7

Бренд: U.S. Divers Страницы: 22

Бренд: Daihan Scientific Страницы: 11

Бренд: Allen-Bradley Страницы: 16

Бренд: Linak Страницы: 2

Бренд: YASKAWA Страницы: 360

Бренд: Nibe Страницы: 20

BACnet 4M230.8I AP

Бренд: WAREMA Страницы: 4

Бренд: Wachendorff Страницы: 35

Бренд: Fright Ideas Страницы: 2

Бренд: Omega Страницы: 56

Бренд: ascon Страницы: 20

MC-5000L Series

Бренд: Lintec Страницы: 2

Бренд: Regin Страницы: 7

Бренд: Kelly Страницы: 31

Бренд: JL Audio Страницы: 2

Бренд: A.B.S. Страницы: 5

Бренд: Vivo Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды