Infineon iMOTION EVAL-M3-IM564 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 47

Infineon iMOTION EVAL-M3-IM564 Скачать руководство пользователя страница 7

User Manual

7 of 47

Revision 1.4

2020-07-16

EVAL-M3-IM564 User Manual

iMOTION

™

Modular Application Design Kit

Main features of EVAL-M3-IM564

2

Main features of EVAL-M3-IM564

EVAL-M3-IM564 is an evaluation board for motor drive applications with single-phase, integrated PFC and 3-

phase IPM. Combined in a kit with one of the available MADK control board options, it demonstrates Infineon’s

motion control IC and IPM technology for motor drives with single-phase PFC.

Main features of CIPOS

™

Mini IPM IM564-X6D/IM564-X6DS include:

• 3 half bridges with TRENCHSTOP

™

20 A/600 V and antiparallel diodes for inverter section

• 20 A/600 V CoolMOS

™

power MOSFETs and rapid switching emitter-controlled diodes for PFC section

• Lead-free terminal plating; RoHS compliant
• Very low thermal resistance due to DCB
• Rugged SOI gate driver technology with stability against transient and negative voltage
• Negative potential allowed up to VS =-11 V for single transmission at VBS=15 V
• Integrated bootstrap functionality
• Overcurrent shutdown
• Temperature monitor
• Undervoltage lockout at all channels
• Low side common emitter
• Cross conduction prevention
• All six switches turn off during protection

The evaluation board characteristics include:

• Input voltage 165~265 V

AC

• Maximum 2800 W motor power output
• Power factor correction
• On board EMI filter
• Current sensing with single shunt
• Auxiliary power supply with 15 V, 3.3 V
• Overcurrent protection
• Overtemperature hardware protection
• Sensing of DC-link voltage
• Thermistor output
• Fault diagnostic output
• Measurement test points compatible with standard oscilloscope probes
•

PCB is 148 mm × 165 mm and has two layers with 35 μm copper each

• RoHS compliant

«
...
5
6
7
8
9
...
»

Содержание iMOTION EVAL-M3-IM564
















































Отзывы:

Нет отзывов