manualshive.com logo in svg

Infineon Cypress BCM4334, Руководство пользователя, Страница: 12 / 38

Поделиться
Скачать
Infineon Cypress BCM4334 Скачать руководство пользователя страница 12

Measuring Current Consumption in Different Power Modes

www.cypress.com

Document No. 002-14914 Rev. *C

11

Generate 4096 slots for 2.56s of activity

1.

In the list of Host Controller & Baseband commands, double-click 

Write_Inquiry_Scan_Activity

.

2.

In HCI Command: Write_Inquiry_Scan_Activity (com4@115200):

a.

For the 

Inquiry_Scan_Interval

, type 

4096

 in the space provided. 

b.

For the 

Inquiry_Scan_Window

, type 

0x18

 in the space provided.

c.

Click 

OK

.

Set the Current IAC Lower Address Portion (LAP) parameters

1.

In the list of Host Controller & Baseband commands, double-click 

Write_Current_IAC_LAP

.

2.

In HCI Command: Write_Current_IAC_LAP (com4@115200):

a.

For the 

Num_Current_IAC

, type 

1

 in the space provided.

b.

For the 

IAC_LAP

, type 

10390288

 in the space provided.

c.

Click 

OK

.

Set the Write Scan Enable parameters

1.

In the list of Host Controller & Baseband commands, double-click 

Write_Scan_Enable

.

2.

In HCI Command: Write_Scan_Enable (com4@115200), in the 

Scan_Enable

 list, select 

Inquiry Scan 

enabled

, and then click 

OK

.

Measure the current consumption

Set the approximate range of the ammeter to 0.2 mA and measure the current being consumed by the DUT.

5.4

Standard Page Scan

This section explains how to set the BCM4324/BCM4334 to Standard Page Scan mode. Steps include the follow-
ing and apply only to the DUT:

■

Set the HCI Control Transport profile.

■

Reset the DUT.

■

Set the Sleepmode parameters.

■

Set the Scan Type.

■

Generate 2048 slots for 1.28s of activity.

■

Set the Write Scan Enable parameters.

This section concludes by specifying the approximate ammeter range setting for measuring the current being con-
sumed by the DUT.

Before you begin, set up and turn on the test equipment and launch Cypress BlueTool.

Set the HCI Control Transport profile

1.

Open a log window. On the 

View

 menu, click 

Log Window

. 

2.

Set the HCI Control Transport profile. 

a.

On the 

Transport

 menu, click 

HCI Control

.

b.

In HCI Control Window Transport:

■

Select 

UART

.

■

In the top 

UART

 list, type the COM port of the PC that the DUT is connected to (

com4

).

■

In the bottom 

UART

 list, select 

115200

.

■

Select the 

CTS flow control

 check box, and then click 

OK

.

Reset the DUT

1.

While in HCI Control, press the 

3 key

 on the keyboard to select the Host Controller & Baseband commands.

2.

In the list of Host Controller & Baseband commands, double-click 

Reset

. 

Содержание Cypress BCM4334







































Отзывы:

Нет отзывов