Inficon PCG55 Series Скачать руководство пользователя | Manualshive

Страница: 48 / 72

background image

48

tina56e1-f (2015-09)

The current ATM threshold setting

•

can be read / written via the diagnostic port

•

is output at the measurement signal output instead of the

pressure signal, can be measured with a voltmeter, and is
displayed on the LCD display after the <SP1> or <SP2>
button is pressed

•

can be read / written via the DeviceNet, Profibus and RS485

interface.

DANGER

DANGER: malfunction
If processes are controlled via the signal output,
keep in mind that by pushing the <SP> button the
measurement signal is suppressed and the cor-
responding threshold value is output instead. This
can cause malfunctions.
Push the <SP> button only if you are sure that no
malfunction will cause.

Programming ATM setpoint

Programmable parameters:
(

→



[3], [4], [5], [6])

Factor of ATM
Low Trip Enable
Low Trip Point Hysteresis

High

Trip

Enable

High Trip Point Hysteresis

Setpoint

Mode

Switching characteristics of the setpoints

→



41.

Diagnostic port

→



[3].

«
...
46
47
48
49
50
...
»

Содержание PCG55 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для PCG55 Series

Бренд: Keller Страницы: 6

Бренд: Danfoss Страницы: 6

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 12

Бренд: National Instruments Страницы: 18

Бренд: National Instruments Страницы: 12

HF scientific AccUView LED

Бренд: Watts Страницы: 40

Бренд: National Instruments Страницы: 12

Бренд: ILX Lightwave Страницы: 126

Бренд: YATO Страницы: 36

Бренд: Interacoustics Страницы: 60

Alta Site Survey Tool

Бренд: Monnit Страницы: 15

Бренд: X-Rite Страницы: 130

Бренд: AEMC Страницы: 20

Бренд: Zhengzhou Minghe Electronic Technology Страницы: 7

Бренд: Omega Страницы: 22

Бренд: LOVATO ELECTRIC Страницы: 9

Бренд: MEWOI Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды