Inalto IOSO605M, Руководство пользователя

Страница: 10 / 28

10
Installation (Continued)
ELECTRICAL CONNECTION:
• Those ovens equipped with a three-pole power supply cable are designed to
operate with an alternating current. The wire for earthling the appliance is
yellow-green in colour.
FITTING ON A POWER SUPPLY CABLE
Opening the terminal board:
• Using a screwdriver, prize the bolt on the side tabs of the terminal board cover
• Unscrew the bolt, pull open the cover of the terminal board.
To install the cable, proceed as follows:
• Remove the wire clamp screw and the three contact screws
L-N –
• Fasten the wires beneath the screw heads using the following color scheme:
Blue (N) Brown (L) Yellow-Green
• Fasten the supply cable in place with the clamp and close the cover of the
terminal board.
CONNECTING THE SUPPLY CABLE TO THE MAINS
Install a standardised plug corresponding to the load indicated on the data plate.
When connecting the cable directly to the mains, install an omni polar circuit
breaker with a minimum contact opening of 3 mm between the appliance and the
mains. The omni polar circuit breaker should be sized according to the load and
should comply with current regulations (the earth wire should not be interrupted by
the circuit breaker).
The supply cable should be positioned so that it does not reach a temperature of
more than 50°C with respect to the room temperature, anywhere along its length,
or protected by insulation sleeping having an appropriate rating.
N. B :Installation in compliance with the consumption declaration
In order to ensure adequate ventilation ,the back panel of the cabinet unit must be removed .Installing the oven
so that it rests on two strips of wood is preferable .If the oven rests on a continuous ,flat surface ,there must be an
aperture of at least 45
×
568mm .
The panels of the adjacent cabinets must be made of heat-resistant material .In particular ,cabinets with a veneer
exterior must be assembled with glues which can withstand temperatures of up to 100
℃
.
In compliance with current safety standards, contact with the electrical parts of the oven must not be possible once it has
been installed.
All parts, which ensure the safe operation of the appliance, must be removable only with the aid of a tool.
To fasten the oven to the cabinet, open the door of the oven and attach it by inserting the 4 wooden screws into
the 4 holes located on the perimeter of the frame.
Electrical Connection
Those ovens equipped with a three-pole power supply cable are designed to operate with an alternating
current .The wire for earthling the appliance is yellow-green in color.
Fitting on a Power Supply Cable
Opening the terminal board:
·
Using a screwdriver ,prize the bolt on the side tabs of the
terminal board cover ;
·
Unscrew the bolt, pull open the cover of the terminal board .
To install the cable, proceed as follows:
·
Remove the wire clamp screw and the three contact screws L-N –
·
Fasten the wires beneath the screw heads using the following color scheme : Blue (N) Brown (L)
Yellow-Green
·
Fasten the supply cable in place with the clamp and close the cover of the terminal board .
Connecting the supply cable to the mains
Install a standardized plug corresponding to the load indicated on the data plate. When connecting the cable
directly to the mains, install an omni polar circuit breaker with a minimum contact opening of 3 mm between the
appliance and the mains .The omni polar circuit breaker should be sized according to the load and should comply
with current regulations (the earth wire should not be interrupted by the circuit breaker).
The supply cable should be positioned so that it does not reach a temperature of more than 50
℃
with respect to
the room temperature ,anywhere along its length , or protected by insulation sleeping having an appropriate
rating.
Before making the connection, check that:
·
The electrical safety of this appliance can only be guaranteed if the cooker is correctly and efficiently
earthed ,in compliance with regulations on electrical safety. Always ensure that the earthling is efficient; if you
have any doubts call in a qualified technician to check the system .The manufacturer declines all responsibility for
damage resulting from a system which has not been earthed.
·
Before plugging the appliance into the mains ,check that the specifications indicated on the date plate (on the
appliance and /or packaging )correspond to those of the electrical mains system of your home .
·
Check that the electrical capacity of the system and sockets will support the maximum power of the
appliance ,as indicated on the data plate .If you have any doubts, call in a qualified technician.
·
If the socket and appliance plug are not compatible ,have the socket replaced with a suitable model by a
qualified technician . The latter, in particular, will also have to ensure that the cross section of the socket cables
are suitable for the power absorbed by the appliance. The use of adapters, multiple sockets and /or extensions, is
not recommended. If their use cannot be avoided, remember to use only single or multiple adapters and
extensions which comply with current safety regulations .In these cases, never exceed the maximum current