background image

 

10 

Before the weld: If the input  air pressure is too low to reach the required  electrode force, a warning will sound, and  the 
machine will display the error message “Pressure too low”. Pressing the button for a second time will force the execution of 
the welding spot with the available air pressure. 
After the weld: If the welding current measured during the spot is 6% less than the setting, the machine will display the 
error message “Current too low” - the welding spot should be checked. 
A message will be displayed at the end of every welding spot, showing the measured welding current and electrode force. 
This  message  is  displayed  on  the  screen  until  a  key  on  the  control  panel  is  pressed,  or  until  a  new  welding  spot  is 
performed, by pressing the B button on the clamp. 

Press  

 for 2 seconds to revert back to standard mode. 

 
GYSTEEL Mode 

The GYSTEEL mode is optional and is configurable in the setup menu that is activated by pressing the mode key for 2 
seconds (GYSTEEL mode on / off). 

The  auto  mode  is  identical  to  normal  mode  except  that  the  user  enters  the 
yield  strength  of  steel.  The  Ys  may  be  found  using  a  durometer  such  as  the 
Gysteel Vision. 
Re: 1-10 corresponds to mild steels. 
Re: 11-18 corresponds to HSS/THSS steels. 
Re: 19-35 corresponds to UHSS steels. 
Re: 36-99 corresponds to boron steel. 

Sheet thickness: it can vary from 0.60mm up to 3.0mm in steps of 0.05mm. 

The C arm used on the clamp. 

The up and down button (key definition diagram, (3) ) scrolls through the 
parameters to modify (sheet thickness, Yield strength, arm used). The + and – 
keys allow modification of each parameter. 

Button A on the clamp allows the thickness of the sheets to be welded to be changed remotely. 
Button B on the clamp allows the user to spot weld with the selected parameters. 

Press 

 for 2 seconds to revert back to standard mode.

 

 
MANUAL Mode 

This mode allows the user to manually select the welding parameters, for example when following instructions from a 
Manufacturer 

 The default settings in manual mode correspond to the settings 
automatically selected in standard mode (thickness and type of sheet, 
electrode force, arm). 
The parameters can be adjusted using the + and – keys (Key Definition 
diagram, (3) ). The up and down keys allow navigation from one 
parameter to the next 

-

Welding current (2000 to 13000 A, steps of 100 A) displayed in kA. 

-Welding time (100 to 850 ms, steps of 10 ms) 
-Electrode force (100 to 550 daN, steps of 5 daN) 
-Arm used on the clamp (number and length) 

 

 
 

 

Before the weld: If the input  air pressure is too low to reach the required  electrode force, a warning will sound, and  the 
machine will display the error message “Pressure too low”. Pressing the button for a second time will force the execution of 
the welding spot with the available air pressure. 
After the weld: If the welding current measured during the spot is 6% less than the setting, the machine will display the 
error message “Current too low” - the welding spot should be checked. 
A message will be displayed at the end of every welding spot, showing the measured welding current and electrode force. 
This  message  is  displayed  on  the  screen  until  a  key  on  the  control  panel  is  pressed,  or  until  a  new  welding  spot  is 
performed, by pressing the B button on the clamp. 
 

Press 

 for 2 seconds to revert back to standard mode. 

 

CAR MANUFACTURER Mode : 

 
The CAR MANUFACTURER mode is optional and is configurable in the setup menu that is activated by pressing the mode 
key for 2 seconds (CAR MANUFACTURER :  ON / OFF).  

 

This  mode  allows  calling,  in  a  nominative  manner,  a  pre-recorded  welding  spot  according  to  a  car  manufacturer  repair 
specification. Select the CAR MANUFACTURER in the left column, then by pressing the (+) key the spots list is displayed on 
the right column. Select the requested welding spot (highlighted); the machine is ready to weld. 

Содержание SPOT 14500 TRAFO

































Отзывы: