Impulse Yamuna Скачать руководство пользователя | Manualshive

Страница: 28 / 38

background image

28

9. ECOMIZER-PRO (type3)

The ECOMIZER-PRO controller is located at the middle panel. It is connected with the
pump and engine by the 2 plugs at the bottom of the control box. This allows the user
to easily remove the middle panel during maintenance

•

To start the ECOMIZER-PRO:

turn the “Off-On-Start” switch on the control box in the “Start”

position.

•

Release the switch and wait until the start screen appears. When no further actions are made
during the shutdown relays (2 minutes on default) the ECOMIZER-PRO will switch itself into
Stand-By. To reactivate the ECOMIZER-

PRO the user has to turn the switch on “start” again,

or when applied (optional), the pump can be started by Remote Control.

•

The “Off” position will shut down the Pump Unit completely. This position can be used as
emergency stop. Make sure the ECOMIZER-

PRO is “Off” while maintaining, repairing,

transporting or being stored.

Starting screen

«
...
26
27
28
29
30
...
»

Содержание Yamuna







































Отзывы:

Нет отзывов

Похожие инструкции для Yamuna

Бренд: G&F Manufacturing Страницы: 17

FCD-JTHMG80-III

Бренд: Haier Страницы: 2

Little Sea-ox FCD-JTHC40-III (E)

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 23

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 2

Бренд: Navien Страницы: 108

Бренд: Ultranatura Страницы: 24

Бренд: Calpeda Страницы: 32

Бренд: RainSoft Страницы: 16

Бренд: Campbell Страницы: 2

Бренд: EXTOL Страницы: 28

LARIUS SIRIO 60:1

Бренд: Samoa Страницы: 46

Бренд: ubbink Страницы: 30

Бренд: E-gas Страницы: 10

Бренд: ProMinent Страницы: 96

Бренд: Flotec Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды