Impulse Yamuna Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 38

background image

26

4.  Connect the lines.
5.  If the pump is dry, the pump housing must first be filled with water.
6.  Perform the daily maintenance.
7.  Check whether there is sufficient fuel in the fuel tank.
8.  Turn on earth switch (1)

9. Turn the switch on the control panel to position 2. The oil pressure and battery charging lamp

must light on.

10. Turn the switch on START position (3). Engine must starting.

WARNING

If vibration occurs during starting, stop the pump immediately and eliminate the
cause before starting again.

11. Let the engine run for five minutes before the pump is connected to the dewatering system.
12. If the engine does not start, press and hold the red handle on the oil-pressure protection. Start

the engine, and release the handle once the engine is running.

«
...
24
25
26
27
28
...
»

Содержание Yamuna







































Отзывы:

Нет отзывов

Похожие инструкции для Yamuna

Бренд: York Страницы: 16

Бренд: TapFlo Страницы: 35

Бренд: Rainman Страницы: 17

Бренд: Calpeda Страницы: 44

Бренд: Calpeda Страницы: 64

Бренд: Calpeda Страницы: 32

45 E Frame Series

Бренд: Danfoss Страницы: 44

ElectriFLEX LD LE Series

Бренд: Bradford White Страницы: 40

Бренд: P.Lindberg Страницы: 54

Бренд: XTline Страницы: 29

Бренд: A.O. Smith Страницы: 28

FLOJET G55 Series

Бренд: Xylem Страницы: 2

Бренд: Dimplex Страницы: 12

Бренд: Waterous Страницы: 7

Бренд: CleanCraft Страницы: 22

Бренд: vacuubrand Страницы: 72

Бренд: TOHATSU Страницы: 99

Бренд: Laars Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды