iMotion SC111 Скачать руководство пользователя страница 94

Страница: 94 / 260

iWaylink Inc.

Search for barcodes that begin with a 1. If a barcode matches, move the

cursor back to the beginning of the data and send 6 characters followed by a

carriage return. Using the barcode above:

Command string: FE31F7F2060D

“Compare characters” command

Hex value for 1

“Move the cursor to the beginning” c

ommand

“Send a number of characters” command

Number of characters to send

Hex value for a CR

The data is output as:

123456

<CR>

EA - Move the cursor to the end

Move the cursor to the last character in the input message. Syntax = EA.

5-4-3 Search Commands

—

Search forward for a character

Search the input message forward for “xx” character from the current cursor
position, leaving the cursor pointing to the “xx” character.

Syntax = F8xx

where

xx stands for the search character’s hex value for its ASCII

code. Refer to the

ASCII Conversion Chart (Code Page 1252), for decimal, hex and character

codes.

Example: Send barcode data that starts after a particular character

Search for the letter “D” in

barcodes and send all the data that follows,

including the

“D.” Using the

barcode above:

Command string: F844F10D

“Search forward for a character” command

Hex value for “D”

“Send all characters” command

Содержание SC111





































































































































































































































































Результаты поиска

Содержание SC111

Отзывы:

Похожие инструкции для SC111

Бренды по названию

Популярные бренды

iMotion SC111, Руководство пользователя

Результаты поиска

Содержание SC111

Отзывы:

Похожие инструкции для SC111

Бренды по названию

Популярные бренды