iMotion SC111 Скачать руководство пользователя страница 207

Страница: 207 / 260

iWaylink Inc.

207

Example

: What is the default value for Codabar Coding Enable?

Enter:

cbrena^.

Response:

CBRENA1[ACK]

This response indicates that the default setting for Codabar Coding Enable (CBRENA)

is 1, or on.

Example

: What is the device’s current setting for Codabar Coding Enable?

Enter:

cbrena?.

Response:

CBRENA1[ACK]

This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to

1, or on.

Example

: What are the device’s se

ttings for all Codabar selections?

Enter:

cbr?.

Response:

CBRENA1[ACK], SSX0[ACK], CK20[ACK], CCT1[ACK], MIN2[ACK], MAX60[ACK],

DFT[ACK].

This response indicates:

•

Codabar Coding Enable (CBRENA) is set to 1, or on

•

Start/Stop Character (SSX) is set to 0,

or Don’t Transmit

•

Check Character (CK2) is set to 0, or Not Required

•

Concatenation (CCT) is set to 1, or Enabled

•

Minimum Message Length (MIN) is set to 2 characters

•

Maximum Message Length (MAX) is set to 60 characters

•

Default setting (DFT) has no value.

8-3 Trigger Commands

You can activate and deactivate the scan engine with serial trigger commands.

First, the scan engine must be put in Manual Trigger Mode by scanning a

Manual Trigger Mode barcode, or by sending a serial menu command for

triggering. Once the scan engine is in serial trigger mode, the trigger is

activated and deactivated by sending the following commands:

Activate: SYN T CR(ASCII 22,84,13)

Deactivate: SYN U CR(ASCII 22,85,13)

The scan engine scans until a barcode has been read, until the deactivate

command is sent, or until the serial time-out has been reached (see "Read

Содержание SC111





































































































































































































































































Результаты поиска

Содержание SC111

Отзывы:

Похожие инструкции для SC111

Бренды по названию

Популярные бренды

iMotion SC111, Руководство пользователя

Результаты поиска

Содержание SC111

Отзывы:

Похожие инструкции для SC111

Бренды по названию

Популярные бренды