IMO D4 Скачать руководство пользователя страница 10

Страница: 10 / 11

D4 0617GB
December 2000

113

D4 23 © IMO AB

Fig. 21

Fig. 20

• Lubricate and fit the O-ring 520A on the seal

cover 520. Fit the seal cover onto the power
rotor shaft 102.

• Fit the screws 521 and tighten them carefully.

• Fit the shaft key 113.

• Fit the coupling half back into place and

lock with locking screw.

• Check that the axial position is the same

as before dismantling. (See fig. 6).

• Put the pump back into the system and

proceed according to instructions under
”Start-up” in the installation manual.

D4 22 © IMO AB

• Fit the O-ring S2 in the seal seat S1.

• Fit the seat S1 in the seal cover 520.

• Lubricate the power rotor shaft, the bellows

unit S5 and the seal ring S4.

• Fit the bellows unit S5 into the front cover

501.

• Fit the seal ring S4. Note the position of the

drive notches on S4 and S5. They need to fit
together.

D4 21 © IMO AB

Fig. 18

Fig. 19

501

520

521

520

520A

102

ATTENTION

Do not use dirty fingers on the seal face.
Keep it clean and dry.

Содержание D4












Результаты поиска

Содержание D4

Отзывы:

Похожие инструкции для D4

Бренды по названию

Популярные бренды

IMO D4, Инструкции по обслуживанию и эксплуатации

Результаты поиска

Содержание D4

Отзывы:

Похожие инструкции для D4

Бренды по названию

Популярные бренды