Immergas MAIOR EOLO 24 4 E Скачать руководство пользователя страница 46

Страница: 46 / 52

STMaE4E and 07/11

MAIOR EOLO 4 E

Technical Documentation

The burner ignites.

The error 01 appears on the display

(wait for the P.C.B. to make 2 ignition cycles).

See error section 01 - b

The error 04 appears on the display

(wait for the P.C.B. to run 5 ignition cycle attempts).

See error section 04.

Yes

The burner stays on after the first

10 seconds.

The error 01 appears on the display

(wait for the P.C.B. to run 2 ignition cycles).

See error section 01 -c

Yes

The error 27 appears on the display Yes

See error section 27

The error 02 appears on the display Yes

See error section 02 - b

The boiler reaches

and maintains the

set central heating

temperature.

Check the Maximum

heating output and

adjust it to maximum

if necessary.

See section D

Yes

The central heating request is satisfied.

The boiler reaches and

maintains the set DHW

temperature.

See section D

Check that,

- the flow rate of domestic hot water is

not greater than the amount the boiler

is able to supply (see technical data,

output, flow rate, ∆T);

- the plate heat exchanger is clean and

replace it, if necessary.

Yes

The domestic hot water request is satisfied.

Содержание MAIOR EOLO 24 4 E





















































Результаты поиска

Содержание MAIOR EOLO 24 4 E

Отзывы:

Похожие инструкции для MAIOR EOLO 24 4 E

Бренды по названию

Популярные бренды

Immergas MAIOR EOLO 24 4 E, Техническая документация инструкция

Результаты поиска

Содержание MAIOR EOLO 24 4 E

Отзывы:

Похожие инструкции для MAIOR EOLO 24 4 E

Бренды по названию

Популярные бренды