C
33
C
33
C
33
C
33
7
4
6
5
1
2
3
1
2
3
4
5
6
7
17
18
19
20
15
INS
TALLER
US
ER
MAINTEN
AN
CE TECHNI
CI
AN
The Kit includes:
N° 1 - Gasket (1)
N° 1 - Female concentric flange (2)
N° 1 - Wall sealing plate (3)
N° 1 - Aluminium tile (4)
N° 1 - Int./exhaust concentric pipe Ø
60/100 (5)
N° 1 - Fixed half-shell (6)
N° 1 - Mobile half-shell (7)
The adaptor kit includes:
N° 1 - Gasket (1)
N° 1 - Adapter Ø 80/125 (2)
The Kit Ø 80/125 includes:
N° 1 - Wall sealing plate (3)
N° 1 - Aluminium tile (4)
N° 1 - Fixed half-shell (5)
N° 1 - Mobile half-shell (6)
N° 1 - Concentric intake-exhaust
terminal Ø 80/125 (7)
The remaining kit components
must not be used
1.15 CONCENTRIC VERTICAL KIT
INSTALLATION.
Type C configuration, sealed chamber and
fan assisted.
Concentric vertical intake and exhaust kit. This
vertical terminal is connected directly to the
outside of the building for air intake and flue
gas exhaust.
N.B.:
the vertical kit with aluminium tile enables
installation on terraces and roofs with a maxi-
mum slope of 45% (approx 25°) and the height
between the terminal cap and half-shell (374 mm
for Ø 60/100 and 260 mm for Ø 80/125) must
always be observed.
Vertical kit with aluminium tile Ø 60/100.
Kit assembly
(Fig. 17
): install the concentric
flange (2) on the central hole of the indoor unit,
positioning gasket (1) with the circular projec-
tions downwards in contact with the indoor unit
flange, and tighten using the screws contained
in the kit.
Installation of the fake aluminium tile: replace
the tiles with the aluminium sheet (4), shaping
it to ensure that rainwater runs off. Position
the fixed half-shell (6) on the aluminium tile
and insert the intake-exhaust pipe (5). Fit the
Ø 60/100 (3) concentric terminal pipe with the
male side (5) (smooth) into the flange (2) up to
the end stop; making sure that the wall sealing
plate has been fitted (3), this will ensure sealing
and joining of the elements making up the kit.
N.B.:
when the boiler is installed in areas where
very cold temperatures can be reached, a special
anti-freeze kit is available that can be installed as
an alternative to the standard kit.
• Extensions for vertical kit Ø 60/100
(Fig. 18)
.
The kit with this configuration can be extended
to
a max. straight vertical length of 14.4 m
,
including the terminal. This configuration
corresponds to a resistance factor of 100. In
this case specific extensions must be requested.
Vertical kit with aluminium tile Ø 80/125.
Kit assembly
(Fig. 19
): to install the kit Ø 80/125
one must use the flanged adapter kit in order
to install the flue system Ø 80/125. Install the
flanged adaptor (2) on the central hole of the
indoor unit, positioning gasket (1) with the cir-
cular projections downwards in contact with the
indoor unit flange, and tighten using the screws
contained in the kit. Installation of the fake alu-
minium tile: replace the tiles with the aluminium
sheet (4), shaping it to ensure that rainwater
runs off. Position the fixed half-shell (5) on the
aluminium tile and insert the intake-exhaust
pipe (7). Fit the Ø 80/125 concentric terminal
pipe with the male side (smooth) to the female
side of the adapter (1) (with lip gaskets) up to
the end stop; making sure that the wall sealing
plate (3) has been fitted, this will ensure sealing
and joining of the elements making up the kit.
• Extensions for vertical kit Ø 80/125
(Fig. 20)
.
The kit with this configuration can be extended
up to a
max. length of 32 m
including the ter-
minal. If additional components are assembled,
the length equivalent to the maximum allowed
must be subtracted. In this case specific exten-
sions must be requested.
