background image

28

STESkW ed 05/06 

EOLO Star 23 kW

Technical Documentation

Technical Documentation

  Technical data.

EOLO Star 23 kW technical data.

-  The flue temperature values refer to an air inlet temperature 

of 15°C.

-  Data relative to d.h.w. performance refer to a dynamic inlet 

pressure of 2 bar and an inlet temperature of 15°C; these 

values are measured at boiler outlet considering that to find 

these declared values mixing with cold water is necessary.

Rated heating power

Min. heating power

Rated heat output (useful)

Min. heat output (useful)

Useful thermal efficiency at rated output

Useful thermal efficiency at 30% rated output

Heat loss at shell with burner On/Off

Heat loss at flue with burner On/Off 

kW (kcal/h)

kW (kcal/h)

kW (kcal/h)

kW (kcal/h)

%

%

%

%

25,1 (21586)

7,9 (6834)

23,8 (20485)

7,0 (6000)

94,9

91,1

0,4 / 0,54

4,7 / 0,02

G20

G30

G31

Gas nozzle diameter

Supply pressure

mm

mbar (mm H

2

O)

1,25

20 (204)

0,76

29 (296)

0,76

37 (377)

Max. working pressure heating circuit

Max. working temperature heating circuit

Adjustable heating temperature

Total volume heating expansion tank

Heating expansion tank precharge

Generator water capacity

Head available with flowrate 1000/h

Hot water production available heat output

Domestic hot water adjustable temperature

Domestic circuit flow limiter

Flow limiter rated delivery min. pressure

Domestic circuit min. pressure (dynamic)

Domestic circuit max. working pressure

Min. drawing domestic hot water

Drawing capacity in continuous duty (∆T 30°C)

Specific capacity (∆T 30°C)

Weight of boiler full

Weight of boiler empty

bar

°C

°C

l

bar

l

kPa (m H

2

O)

kW (kcal/h)

°C

l/min

bar

bar

bar

l/min

l/min

l/min

kg

kg

3

90

35 - 80

3,95

1,0

3,5

25,5 (2,6)

23,8 (20485)

35 - 55

8

1,0

0,3

10

1,5

11,1

10,7

38

34

Electrical connection

Rated absorption

Installed electrical power

Power absorbed by circulating pump

Power absorbed by fan

Appliance electrical system protection

V/Hz

A

W

W

W

-

230/50

0,79

135

73

43

IPX4D

G20

G30

G31

Mass flow of fumes at rated power

Mass flow of fumes at min. power

CO

2

 at Q. Rated/Min.

CO with 0% O

2

 at Q. Rated/Min.

NOX with 0% O2 at Q. Rated/Min.

Temperature of fumes at rated power

Temperature of fumes at min. power

kg/h

kg/h

%

ppm

ppm

°C

°C

52

51

6,9 / 2,1

53 / 53

62 / 17

107

83

52

42

8,0 / 3,0

79 / 66

80 / 20

105

86

54

44

7,7 / 2,8

28 / 15

75 / 20

109

83

NO

X

 class

NO

X

 weighted

CO weighted

-

mg/kWh

mg/kWh

3

106

89

Type of appliance

C12 /C32 / C42 / C52 / C82 / B22 / B32

Category

II2H3+

                                         http://serviceimmergas.ro

Содержание EOLO Star 23 kW

































Отзывы: