Immergas EOLO Star 23 kW Скачать руководство пользователя страница 17

Страница: 17 / 32

STESkW ed 05/06

EOLO Star 23 kW

Technical Documentation

Loads.

This board is always powered regardless of the position of the functioning button (S2)

(see integrated board operation)

Integrated board

It is powered by the integrated board when there’s either a central heating or antifreeze

request.

It permits circulation in the primary circuit.

Boiler circulator

(M1)

It is powered at mains voltage by the integrated board when it is necessary to ignite the

burner.

It permits the ﬂow of gas to the burner.

Gas valve (Y1)

(main coils)

It is controlled by the integrated board that provokes a spark between its end and the

burner surface that ignites the air/gas mix.

Ignition electrode

(E1)

It ensures the ﬂow of air inside the sealed chamber and the exit of fumes produced by

combustion.

It is powered by the integrated board.

Fan

(M20)

Low voltage circuit.

This device is to control the appliance remotely

(SUMMER / WIN-

TER selection, setting and indicating temperatures, displaying alarms,

resetting, etc.)

and acts as a weekly timer/room thermostat.

If the CRD is installed the X40 jumper must be removed.

Remote digital control

(CRD)

(optional)

See Remote

Digital Control

Operation

(CRD)

This switch acts on the integrated board after some domestic water

has been drawn, causing the boiler to work in the d.h.w. mode.

When idle it enable operation in the central heating mode.

D.h.w. ﬂow switch

(S4)

Interrupted

contact

Safety devices and controls.

When pressure in the boiler circuit is below 0.3 bar the burner

switches oﬀ.

System pressure switch

(S5)

Interrupted

contact

This acts on the integrated board and enables burner operation

when the fumes are expelled correctly.

When closed and the fan is oﬀ, it does not enable the start of the

ignition cycle.

Flue pressure switch

(S6)

Changing

contact

http://serviceimmergas.ro

Содержание EOLO Star 23 kW

































Результаты поиска

Содержание EOLO Star 23 kW

Отзывы:

Похожие инструкции для EOLO Star 23 kW

Бренды по названию

Популярные бренды

Immergas EOLO Star 23 kW, Техническая документация инструкция

Результаты поиска

Содержание EOLO Star 23 kW

Отзывы:

Похожие инструкции для EOLO Star 23 kW

Бренды по названию

Популярные бренды