8
IMER INTERNATIONAL S.p.A.
SPIN 15
PROBLEMS
CAUSES
CORRECTIVE ACTION
Machine does not start
Electric current
-
No current delivered to connector of site panel (fuses?)
- No power delivered to machine
(defective connector connection? loose cable?)
- Main ON/OFF (thermal cutout) switch not turned on
- Main switch/inverter (3-PHASE version only) set to position 0
- Mixing chamber open
(thermal magnetic switch does not engage)
- Emergency pushbutton pressed (release)
- Check points listed alongside
Thermal cutout trips on
start-up
Material in hopper
- Material has hardened in the hopper
- The type of material requires more water for mixing
- Completely empty the hopper and restart with new material
- Increase the quantity of water delivered
Material consistency not
constant; too hard or too
fluid
Water supply insufficient
- Water hose bent
- Pump inlet water filter clogged
- Pressure reducer water filter clogged
- Pressure reducer faulty
- Check points listed alongside
The water continues to exit
from the mixing chamber
when machine is
stationary
Solenoid valve faulty
- Contact an authorised IMER service centre
Material does not exit the
offload port
Mixing chamber clogged
- The container used for offload is too high and does not enable
the material to flow out
- The offload port is clogged
- Check points listed alongside
Mix not optimal
The type of material used is not suitable
- Not all products on the market can be mixed with this type of high
speed mixing system
- Mixing shaft worn
- Consult the material manufacturers to check compatibility
- Replace shaft
INDICATOR LIGHT
ON
OFF
15 SILICA DUST WARNING
Grinding/cutting/drilling of masonry, concrete, metal and other materials
with silica in their composition my give off dut or mists cintainig crystalli
-
ne silica. Silica is a basic component of sand, quartz, brick clay, granite
and numerous other minerals and rocks. Repeated and/or substantial
inhalation of airborne crystalline silica can cause serious or fatal respira-
tory diseases, including silicosis. In addition, California and some other
authorities have listed respirable crystallinesilica as a substance known
to cause cancer. Whwn cutting such materials, always follow respiratory
precautions.
Use appropriate NIOSH-approved respiratory protection where dust ha-
zard may occur. Paper masks or surgical masks without a NIOSH appro-
val number are not recommended because they do little to protect the
worker. For more information about respirator programs, including what
respirators have received NIOSH approval as safe and effective, please
visit the NIOSH website at:
http://www.cdc.gov/niosh/topics/respirators
Observe OSHA regulations for respirator use (29 C:F.R. § 1910.134).
Visit http://www.osha.gov for more information.
Your risk from these exposures varies depending on how often you do
this typer of work. To reduce your exposure to these chemicals, work
in a well-ventilated area, and work with approved safety equipment,
such as dust masks that are specially designed to filter out microscopic
particles. Where use of a dust extraction device is possible, it should be
used. To achieve a high level oof dust collection, use an industrial HEPA
vacuum cleaner. Observe OSHA 29 CFR part 1926.57 and 1926.103
16.SCRAPPING
The machine must be disposed of according to the current
regulations.
The barred bin symbol indicates that at the end of its service life
the product must be scrapped separately from other materials.
The manufacturer is responsible for separate scrapping of the
equipment at the end of its service life. The user must therefore
contact the manufacturer and follow the instructions given by
the latter for separate scrapping of the equipment at the end of
its service life.
Separate scrapping for subsequent recycling, treatment and
eco-compatible disposal contributes to avoiding negative effects
for the environment and for the health of persons, and promotes
the reuse/recycling of the materials of which the equipment is
fabricated.
Incorrect/illegal scrapping is punishable by law.
California proposition 65 message
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contain chemicals know (to the State of
California) to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
-Lead, from lead-based paints
-Crystalline silica, from bricks and cement and other masonry products
-Arsenic and chromium, from chemically treated lumber
For further information , consult the following sources:
http://www.osha.gov/dsg/topics/silicacrystalline/index.html
http://www.cdc.gov/niosh/docs/96-112/
http://oehha.ca.gov/prop65/law/P65law72003.html
http://www.dir.ca.gov/Title8/sub4.html
http://www.P65warnings.ca.gov
