2
IMER U.S.A. Inc.
COMBI 350
Dear Customer,
Congratulations on your choice of purchase: IMER saws are the result of
years of experience and is equipped with all the latest technical innovations.
WORKING IN SAFETY
To work in complete safety, read the following instructions carefully.
- This OPERATION AND MAINTENANCE manual must be kept on site
by the person in charge, e.g. the SITE FOREMAN, and must always be
available for consultation.
- The manual is to be considered integral part of the machine and must
be kept for future reference (EN 292/2) until the machine is disposed of.
If the manual is damaged or lost, a replacement may be requested from
the saw manufacturer.
- The manual contains important information regarding site preparation,
machine use, maintenance procedures, and requests for spare parts.
Nevertheless, the installer and the operator must both have adequate
experience and knowledge of the machine prior to use.
- To guarantee complete safety of the operator, safe operation and long
life of equipment, follow the instructions in this manual carefully, and
observe all safety standards currently in force for the prevention of accidents
at work (use of safety footwear and gloves in accordance with S.I. N°3073
of 30/11/92).
Pay special attention to warnings bearing the following symbol.
Safety glasses or a protective visor must be worn at all
times.
MAKE SURE THAT SIGNS ARE LEGIBLE.
It is strictly forbidden to carry out any form of modification
to the steel structure or working parts of the machine.
- IMER INTERNATIONAL declines all responsibility for non-compliance
with laws and standards governing the use of this equipment, in particular;
improper use, defective power supply, lack of maintenance, unauthorised
modifications, and partial or total failure to observe the instructions contained
in this manual.
2. DESIGN STANDARDS
COMBI 350 saws are designed and manufactured according to the
following standards: I.E.C. 34.4; EN 89/392 (91/368/CEE); CEI EN 60204.
3. NOISE EMISSION LEVEL
Operator exposure to sound emission levels (continuous sound pressure
levels equal to A weighting); the COMBI 350 saw noise emission level
during cutting is 93 dB(A) with continuous rim blade.
4. CUTTING SPECIFICATIONS
This saw model has been specially designed by IMER for cutting stone,
ceramics, marble, granite, concrete and similar materials. Only water-
cooled diamond blades with continuous or segmented edges must be
used. Under no circumstances must dry cutting blades be used or
materials other than those specified above. IMER INTERNATIONAL
declines all responsibility for damage caused by improper use of the
above machine.
TECHNICAL DATA
COMBI 350
350/600
350/1000
Blade rpm
rpm
2150
2040 / 2150
Blade diameter
inc
14''
Blade mounting hole
inc
1''
Motor rating
Hp
3.0
1.5 / 3.0
Motor rpm
rpm
3450
3260 / 3450
Cutting table
dimensions
inc
20'' x 31''
20'' x 46''
Overall dimensions
inc
47'' x 34'' x 51''
63'' x 34'' x 51''
Overall dimensions for
transport
inc
51'' x 28'' x 37''
67''x 31'' x 37''
Weight
lb
253
287
Weight for transport
lb
298
342
Blade rotation
direction(seen from
blade clamping flange)
ANTI - CLOCKWISE
Current
A
11
13.4 / 11
Voltage
V
230
115 / 230
Frequency
Hz
60
5. CUTTING CAPACITY
- Max. thickness (inc): 5'' (90°); 3'' (45°)
- Workpiece width (inc): max. 20'' ; min 2''
- Length:
COMBI 350/600
COMBI 350/1000
thk. x l (inc)
1'' x 24''
1'' x 40''
3'' x 22''
3'' x 38''
(*) 90° cut from above
5'' x 21''
5'' x 37''
5'' x 28'' (*)
5'' x 43'' (*)
(**) 45°
45 x 21'' (**)
70 x 37'' (**)
6. WARNING
- Do not load the saw with workpieces that exceed the specified weight
(max. 90 lb).
- Ensure stability of machine and workpiece before, during or after cutting.
Install supplementary support surfaces at the same height as the
worktable.
- Respect the environment; use suitable receptacles for collection of
cooling water contaminated with cutting dust.
7. SAFETY PRECAUTIONS
IMER saws are designed for work on construction sites and under
conditions of natural light and in workshops under conditions of natural
or artificial lighting of minimum 500 LUX.
Fig. 1 MACHINE LAY-OUT
1
TELESCOPIC LEG
2
SPRAY GUARD
3
MOTOR
4
BLADE SUPPORT
ARM
5
WATER PUMP
6
GUIDE
7
MAIN SWITCH
8
WORKTABLE
9
WATER TANK
10
BLADE GUARD
11
EARTHING SCREW
12
HEAD BLOCKAGE
Fig. 1 - Machine Lay-out
