background image

Chapter 8

Maintenance

62

175-100423-00

1

Press the power off button on the front panel (

Figure 8-1

on page 61) for 5 seconds to remove the power

supply to the system.

2

Unplug both power cords from the system or wall outlets to remove the standby power to the system.

3

If necessary, label and disconnect all remaining cables to the NXAMP3801HDX/HDI.

4

Use a grounded wrist strap designed to prevent static discharge when handling components.

Figure 8-2

Knurled captive screws

5

Loosen the two knurled captive panel screws on the back of the NXAMP3801HDX/HDI (see

Figure 8-2

)

and slide the cover backwards and off the chassis.

Replacement

1

To replace the cover on the chassis:

a

Side the cover forward toward the front of the chassis.

b

Secure with the two knurled captive screws (see

Figure 8-2

) .

2

Reconnect any cables removed during the chassis cover

Removal

on page 61.

Replacing the Onboard CR2032 Battery

The battery on your motherboard may be old. Check to verify that it still supplies

~

3

VDC, if not:

1

To gain access to the CMOS battery, refer to

Chassis Cover

on page 61.

2

Refer to

Figure 8-3

on page 63 for battery location.

3

When replacing the onboard battery make sure to handle the used battery carefully. Do

not damage the battery in any way; a damaged battery may release hazardous
materials into the environment.

4

Using only a CR2032 CMOS battery, install the onboard battery per

Figure 8-4

on

page 63, upside down to avoid possible explosion.

5

Please comply with the regulations set up by your local hazardous waste management

agency to dispose of your used battery properly.

6

Slide the chassis cover back onto the chassis and secure with the two knurled captive

screws.

7

Reconnect all marked cables and power cords.

8

Press the power on button on the front panel (

Figure 8-1

on page 61) for 5 seconds.

9

Press

DEL

to go to the

BIOS

setup screen.

10

If your CMOS settings have been lost, go to

AMI BIOS Recovery

on page 67.

Содержание Nexio AMP NX3801 HDI Gen6











































































Отзывы: