28
9. TECHNICAL CHARACTERISTICS
RF input
• DVB-T FTA, MPEG-2, COFDM
• Frequency band : 170-858 MHz
• Signal level : 29-99 dB
μ
V
• COFDM modes : 2K and 8K
• Channel bandwidth : 6 / 7 / 8 MHz
• Loop-through bandwidth : 47-862 MHz
• Indoor antenna remote powering : +5 VDC
MPEG-2 decoding
• Standard MPEG-2 MP@HL
A/V inputs/outputs
• TV SCART : RGB out, PAL/NTSC out, stereo audio out
• VCR SCART : PAL/NTSC in/out, stereo audio in/out
• A/V jack : PAL/NTSC out, stereo audio out
Front panel
• Type-A female USB2 port
• Red/green LED indicator
• Infrared sensor
Rear panel
• 1x female IEC 169-2 (RF input)
• 1x male IEC 169-2 (RF loop-through output)
• 2x SCART (TV , VCR)
• 1x 3.5 mm mini-jack
• 1x DC jack (12V input)
Power supply
• AC in (power supply unit) : 100-240 V,
~
50/60 Hz
• DC out (power supply unit) / DC in (receiver) : +12 VDC
• Consumption (receiver) : 5.5 W (max)
Accessories
• 44-button remote control
• Batteries : 2x 1.5 V (AAA - LR03)
• 1.2 m SCART cable [For Australian market : 1x 3.5 mm Jack - (3x) RCA cable]
• DC power supply with bipolar plug
• User manual
General
• Operating temperature : 0°C to +45°C
• Relative humidity : 25 to 75%
• Dimensions (width x height x depth) : 210 x 30 x 90 mm
• Weight : 270 g
Software
• Multi-language OSD
• List of favourite channels
• Electronic Programme Guide (EPG)
• Parental control
(channel and configuration lock)
• Functions for ordering, renaming, sorting and deleting channels
• Subtitles and teletext
(if available)
• Last channel memorised and previous channel button
• PAL/NTSC support
• Image zoom
• Scheduling of messages and channel tuning
• Quick software updating
• MPEG-2 recording to external hard disk or flash-drive
- instant
- scheduled
• Multimedia reader
(MP3, JPEG, MPEG-2, MPEG-4, DivX 3.11)
• Games
29
10. APPENDIX
Troubleshooting
Problem
Possible cause
What to do
There is no image or sound
The TV set is not receiving a signal from
the
SMARTmini
receiver or is not set up
correctly
Check that all of the devices are turned on
and connected correctly. Check that the
television set is using the appropriate A/V
input
There is an image but no
sound
"Mute" is activated on the receiver or the
TV set
Check the volume setting on the receiver
and on the TV set
The image and the sound
cut out temporarily or
"freeze"
The signal received through the antenna
is weak
Check the signal level indicated on the
information screen for that channel (INFO
button, pressed twice). Consult an antenna
technician to ensure that the antenna
orientation is correct.
A particular channel cannot
be found
The corresponding signal through the
antenna is very weak
Consult an antenna technician to ensure
that the antenna is correctly installed
The remote control does not
work
The batteries have run out
The remote control does not point
correctly
There is an obstacle between the
receiver and the remote control
The receiver has locked up
Change the batteries
Point the remote control at the front panel of
the receiver
Remove any obstacles preventing direct
visual contact
Wait a few minutes. If the receiver does not
recover, unplug and plug the power supply
The PIN number used to
lock channels has been
lost
Use the "Software update" option. You will
have to search for the channels and
configure the receiver again, using the
default PIN number, "0000".
The receiver does not
work after having updated
the software
This is normal. The update process
deletes all of the channels and any
personal settings.
Search for the channels and configure the
receiver again
Technical Assistance
If you experience any doubts or difficulties using your
SMARTmini
receiver, contact the establishment where
you purchased the device. Do not forget to present the sales receipt.
