Ikegami HTM-1990R M Скачать руководство пользователя страница 46

Страница: 46 / 54

4-8 Messages Displayed on the Screen

Message

Explanation

ALL LOCK

Cause:

This message is displayed during the LOCK mode (see 4.7(7)) or when

FILE 1

FILE 2

FILE 3

switch is pressed.

Action:

Release the LOCK mode (UNLOCK), and resume the operation.

PRESET&FILE LOCK

Cause:

This message is displayed when

CHANGE PRESET

switch or

STORE FILE

switch is

pressed during the

PRESET FILE

setting in the LOCK mode (see 4.7(7)).

Action:

Release the LOCK mode (UNLOCK), and resume the operation.

CHANGE PRESET

→

Cause:

This message is displayed when each

PRESET

switch is pressed while

CHANGE PRESET

switch is OFF.

Action:

Set

CHANGE PRESET

switch to ON, and resume the operation.

CHANGE PRESET

→

OFF

Cause:

This message is displayed when each

PRESET

switch is pressed while

CHANGE PRESET

switch is ON.

Action:

Set

CHANGE PRESET

switch to OFF, and resume the operation.

DELAY

→

OFF

Cause:

This message is displayed when

BRIGHT PRESET

switch is pressed in the DELAY mode.

Action:

Cancel the DELAY mode, and resume the operation.

APT

→

Cause:

This message is displayed when

APT PRESET

switch is pressed while

APT

switch is

OFF.

Action:

Set

APT

switch to ON, and resume the operation.

STORE FILE

→

OFF

Cause:

This message is displayed when

CHANGE PRESET

switch is pressed while FILE 1 to

FILE 2 are blinking by pressing

STORE FILE

switch.

Press

STORE FILE

switch to cancel the selection prompt (blinking), and resume the

operation.

MANUAL

→

OFF

Cause:

This message is displayed when

PRESET

switch is pressed while any MANUAL control

is set to the MANUAL mode.

Action:

Set to the PRESET mode, and resume the operation.

MENU

→

OFF

Cause:

This message is displayed when

CHANGE PRESET

switch is pressed with MENU on.

Action:

PRESET

data cannot be changed with MENU on. Exit the MENU, and resume the

operation.

NO OPERATION

Cause:

This message is displayed when the operation is wrong or invalid.

Action:

Check the operation procedure and try again.

ENTER CORRECT PASSWORD

Cause:

This message is displayed when wrong password is entered while setting the LOCK
mode in the MENU 5.

Action:

Check the password and enter correctly.

Cause:

This mark is displayed when the MPU BOARD data backup lithium battery is low.

Action:

Replace the battery immediately. Refer to the service manual for the replacement method.

Содержание HTM-1990R M























































Результаты поиска

Содержание HTM-1990R M

Отзывы:

Бренды по названию

Популярные бренды

Ikegami HTM-1990R M, Руководство по эксплуатации

Результаты поиска

Содержание HTM-1990R M

Отзывы:

Бренды по названию

Популярные бренды