Ikegami HTM-1990R M страница 37 Скачать руководство пользователя

Страница: 37 / 54

(8) Adjusting the screen distortion

Screen distortion

The

SIDE PIN

and

TRAPEZOID

controls are

provided to adjust the screen distortion.

Pressing the

EXPAND

switch executes these

adjustments alternately.

These two preset data can be set differently for

each signal format. In the case of HDTV signal,

different data is set also for 16:9 and HD 4:3 SCAN.

Precautions

As the SIDE PIN and TRAPEZOID settings are

stored as the data for each signal format, do not

perform the following operations during the

setting.

Performing any of the switching below will call the

data in a different format and clear the data you

are now working on.

Switching channels

Changing input signal format

Switching SCAN

Switching ASPECT

Adjustment procedure

①

Input signal

Check the MENU 1 format is set properly to the

signal format to be changed.

For details of the format setting, refer to 4.7(3) in

this manual.

Input a crosshatch signal or select the crosshatch

internal TEST signal.

②

Adjusting TRAPEZOID

Set the EXPAND switch to ON. The TRAPEZOID

adjustment mode is entered. Adjust the trapezoid

as shown in the figure below.

③

Adjusting SIDE PIN

Set the

EXPAND

switch to ON again. The SIDE

PIN adjustment mode is entered. Correct the side

pin distortion as shown in the figure below.

④

Before proceeding with the adjustments and

changes in

②

and

③

for a different format, first

store the changed data and then switch the signal

to a different format.

<NG>

<OK>

<NG>

<OK>

(9) Adjusting the screen size

Screen size

Set the screen size using HEIGHT and WIDTH.

The following four sizes can be set for these two

data per signal format (three sizes for HDTV).

Individual data is provided for all formats which

can be input, for the following sizes.

SCAN

switch:

NORMAL SCAN

UNDER SCAN

ASPECT

switch:

4:3 SCAN

16:9 SCAN

Precautions

As the HEIGHT and WIDTH settings are stored

as the data for each signal format, do not perform

the following operations during the setting.

Performing any of the switching below will call the

data in a different format and clear the data you

are now working on.

Switching channels

Changing input signal format

Switching SCAN

Switching ASPECT

Adjustment procedure 1

(UNDER SCAN (HD 16:9, SD 4:3/16:9)

Adjust HEIGHT and WIDTH for HDTV 16:9 and

SDTV 4:3/16:9 UNDER SCAN as follows.

①

Input signal

Check the MENU 1 format is set properly to the

signal format to be changed.

For details of the format setting, refer to 4.7(3) in

this manual.

The input signal should be one having a circle

pattern, which can display video on the whole

active screen area.

②

Adjusting HEIGHT and WIDTH

Set the desired aspect using the

ASPECT

switch,

and set UNDER SCAN using the

SCAN

switch.

Set the MARKER switch to ON, and select the

100% marker.

Adjust HEIGHT and WIDTH so that the 100%

marker size becomes the UNDER SCAN size in

the following table.

<UNDER SCAN Sizes>

ASPECT

FORMAT

HEIGHT

WIDTH

4 : 3

270mm

360mm

16 : 9

SD/HD

203mm

360mm

HEIGHT

WIDHT

HEIGHT

WIDHT

〈4：3（UNDER）size〉

〈16：9（UNDER）size〉

* Before proceeding to adjust another SCAN size,

be sure to press the CHANGE PRESET switch
now to store the current data.

Содержание HTM-1990R M























































Результаты поиска

Содержание HTM-1990R M

Отзывы:

Похожие инструкции для HTM-1990R M

Бренды по названию

Популярные бренды

Ikegami HTM-1990R M, Руководство по эксплуатации

Результаты поиска

Содержание HTM-1990R M

Отзывы:

Похожие инструкции для HTM-1990R M

Бренды по названию

Популярные бренды