Ikarus Team Sevilla Ikarus OSD Скачать руководство пользователя страница 35

Страница: 35 / 60

Initial Configuration

Make the default settings of "Ikarus OSD ". Not normally required, as OSD will be set by

default when connecting for the first time. It is recommended that you use the save and restore
complete OSD configuration functions, to easily retrieve the configuration if necessary.

•

Video System: Select between PAL and NTSC.

•

GPS Baud Rate: Speed in bits per second of GPS serial port.

•

Control Input: Choose between a normal servo input and a PPM input with information of all
channels. PPM mode is not available in all RC receivers.

•

PPM channel: In case that PPM mode is selected, you must choose which of the channels
present in the PPM frame it’s used for control.

•

Mix: Allow to select between Normal (no mixing), Elevon (A Elevator), or V-tail
(El Tail). "Elevon" mode it’s usually used in flying wings.

Page. 35/60

Содержание Ikarus OSD





























































Результаты поиска

Содержание Ikarus OSD

Отзывы:

Похожие инструкции для Ikarus OSD

Бренды по названию

Популярные бренды

Ikarus Team Sevilla Ikarus OSD, Руководство пользователя

Результаты поиска

Содержание Ikarus OSD

Отзывы:

Похожие инструкции для Ikarus OSD

Бренды по названию

Популярные бренды