background image

7

Following is a list of substances that can be ground dry:
Grain, barley, corn, malt, pectin, roasted coffee, bark, roots, nutshells, bones, 
ergot, compressed materials, peat, cellulose, pharmaceutical, artificial, fertilizers, 
feed materials, spices, resin, potash, seeds, salts, slag.
Tough grinding material must be cooled, for example by adding pulverized dry ice 
to the grinding container.
The grinding material must be initially broken down into pieces with a diameter of 
1 cm (feed granularity 10 mm, the size of a grain of corn is ideal).

Cutting milling:

The 

A 11 basic

 with the A 11.2 cutting blade reduces bulky, elastic fibrous and 

soft materials with high cellulose content. Mixed goods such as trash must be 
free of iron and non-iron metals. The feed material must not be too moist or fatty. 
Otherwise the material may adhere to the sides of the grinding container.

Following is a list of some materials that can be reduced:
Leaves, fibre, spices, grain, hops, cardboard, paper, hay, plastics, tobacco, peat, 
feed goods, dough and roots.
The feed granularity should be no greater than 10 mm.
For moist and sticky feed material (for example fish, meat), reduction is also 
possible by adding water. This prevents the grinding material from adhering to the 
walls of the grinding container, and the blades continue to engage the grinding 
material.

If water is added, the grinding container should not be 
filled to more than 50% capacity. The mill must only 
be used in an upright position in this case (must not be 

agitated or turned on its head).

Materials that are not listed above should only be 
reduced in the 

A 11 basic

 after confirmation from 

IKA

especially if there is uncertainty about the danger of 

explosion (dust explosion as a result of electrostatic charge).

NOTICE

WARNING

Unpacking

Delivery scope:

A 11 basic

 (with grinding container A 11.5 and beater A 11.1)

-  A set of tools 

-

 User guide

-

 Warranty card.

Unpacking:

-  Please unpack the device carefully.
-  Any damage should be notified immediately to the shipping agent (post office, 

railway network or logistics company).

Useful information

The analysis mill can be used for a wide range of applications. The list of grinding 
materials given above is not complete. It is possible to expand the range of 
application further by means of grinding experiments with corresponding grinding 
procedures and sample preparations.

Impact milling:

The 

A 11 basic

 with a beater reduces soft, medium-hard and brittle materials 

with a Mohs’ hardness of up to 6 (felsite: 6 Mohs; quartz: 7 Mohs). For greater 
levels of hardness, the wear and tear on the pulverization tool is very high and 
grinding therefore becomes uneconomical. If the 

A 11 basic

 is used for grinding 

materials with hardness greater than 4 Mohs, the A 11.3 beater, which is more 
resistant to wear and tear, must be used. This prevents the sample from being 
contaminated by bits of the grinding tool broken off by wear and tear.
Everything that breaks, is dry, and does not have a high fat content can be ground. 

Содержание A11 basic


















Отзывы: