IKA 06-5819 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 48

background image

IKA

®

-WERKE

8

1.4.4 Basic safety information during normal operation

Danger

Before switching on the machine, obtain information on
how to behave in the event of abnormal occurrences.

Danger

The machine may only be operated by appropriately
trained and authorised persons familiar with the operat-
ing instructions (and those for the subassemblies) and
capable of working according to them.

Danger

At working chamber temperatures exceeding 65°C, there
is a danger of burning at the container and supply pipes.
In this case, the operator must apply protection against
accidental contact with hot components.

Caution

The machine may not run dry!
The mechanical seal must always be surrounded by
liquid.

Info

The machine is not suitable for adding and processing
purely dry substances. This can result in serious dam-
age to the device.

Info

When changing the dispersion material, check whether
the materials of the axial-face seal and O-ring are still
suitable. It may be necessary to replace these compo-
nents with other materials. If in doubt, contact the sup-
plier.

Info

Following all assembly work, free movement of the drive
shaft must be ensured by manual turning before switch-
ing on the drive. Secure the drive against unauthorised
activation.

«
...
8
9
10
11
12
...
»

Содержание 06-5819

















































Отзывы:

Нет отзывов

Похожие инструкции для 06-5819

Бренд: ICS Schneider Messtechnik Страницы: 124

Бренд: GE Страницы: 802

Бренд: iET Страницы: 17

Бренд: Datavideo Страницы: 50

Бренд: Waterous Страницы: 90

Бренд: Campbell Страницы: 14

Бренд: Baroness Страницы: 40

Бренд: Baroness Страницы: 40

Бренд: Garmin Страницы: 12

Бренд: Garmin Страницы: 13

Бренд: IDEAL Networks Страницы: 10

Бренд: EuroLite Страницы: 28

Бренд: LAPPSET Страницы: 16

Бренд: ParaBody Страницы: 6

Бренд: ParaBody Страницы: 11

Бренд: Qiagen Страницы: 48

Бренд: Qiagen Страницы: 162

Бренд: Qazqa Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды