background image

3 MAINTENANCE 

MINIDUMPER 

CARRY 107 

 

32 

3.8  UNUSUAL OPERATING CONDITIONS. 

 
Special problems in maintenance and operation are caused by unusual conditions such as extremes in heat, cold and 
humidity, high altitude, salt water, and dusty or sandy work sites. When operating under such conditions, special 
precautions must be taken to prevent machine damage, minimize wear, and avoid component deterioration. 
 

EXTREME COLD. 

 
1. 

Condensation in the fuel tank contaminates the fuel supply with water, which can freeze in the fuel lines and block 
the fuel flow to the engine. To minimize this possibility, keep the tank as full as is practical during cold weather. This 
may entail refilling the tank more frequently than usual, but the inconvenience is small compared to clearing a 
blocked fuel line. 
If water should be noticed in the fuel supply, drain the tank and refill it with uncontaminated fuel. 

 
2. 

Lubricate the machine with the lubricants recommended for cold weather operation in the Lubrication Section. If 
necessary, change the engine oil and other lubricants in order to conform to the recommendations. 

 
3. 

The battery is probably the most sensible element to low temperatures. Freezing temperatures of battery electrolyte 
is as higher as the more discharged battery. When this can occurs, be sure that battery is always charged, mainly 
when you know that the machine has not been working for a long time. Further, battery would discharge also when 
terminals should be covered by ice or snow, by causing a short-circuit. Keep dried both terminals and clamps. Keep 
away an eventual beginning of corrosion, by using water and sodium carbonate. In case of a long working stop at 
very low temperatures, is advisable to remove battery, by keeping it in a sheltered place. 

 

 

 
4. 

Special attention must be given to the hydraulic oil during very cold weather.  

 

 

 
5. 

At the end of the work period, or whenever the machine is to be left idle for extended periods, prevent it from being 
frozen to the ground by parking it on wood, concrete, asphalt or mat surface. 

 

EXTREME HEAT. 

 
Like extreme cold, extreme heat requires that precautions be taken with respect to the cooling system, the battery and 
lubrication. Protect the machine by performing the following recommended procedures. 
 
1. 

High temperatures necessitate the use of lubricants which are both more viscous and which resist deterioration at 
higher operating temperatures. Refer to the Lubrication Section and lubricate the machine using the lubricants 
recommended for the expected temperatures. 
Crankcase oil is particularly important because it helps dissipate heat. Check the oil level frequently and add oil as 
required to maintain required level. Too little oil will hinder heat dissipation. 

 
2.  Increased evaporation rates will cause the battery electrolyte level to fall more rapidly during very hot weather. 

Check the level frequently and add distilled water as required to maintain the proper level. 

 
3.  Air circulation around the engine and battery must not be restricted. Keep air intake and exhaust openings clear of 

leaves, paper or other foreign matter which may restrict air flow. 

 
4.  Keep the engine clean of dirt. grease and other substance s which inhibit heat dissipation. 
 
5.  Avoid prolonged periods at idle and shut the engine down if operations are interrupted.  
 
 

 
B

EFORE ANY WORKING OPERATION OF THE MACHINE

,

 HEAT UP HYDRAULIC OIL

,

 AS INDICATED IN THE  

PARAGRAPH 

1

 

-

 

1. 

    WARNING 

 
W

ATER ADDED TO THE BATTERY CAN FREEZE BEFORE IT MIXES WITH THE ELECTROLYTE

D

URING VERY COLD WEATHER

,

 ADD WATER TO THE BATTERY JUST PRIOR TO

,

 OR DURING 

OPERATION OF THE MACHINE

I

F THE MACHINE IS NOT TO BE RUN

.

 

W

ATER MAY BE ADDED IF AN EXTERNAL CHARGER IS 

CONNECTED TO THE BATTERY

     CAUTION 

Содержание IHIMER CARRY 107

















































Отзывы: