-6-
www.igmtools.com
Pic. 3
5. Assembly
5.1 Unpacking
Your 3HP Mobile Dust Cyclone comes packed in a single box. Before
attempting to assemble this machine, follow these directions for
unpacking:
1. Carefully cut the banding straps and remove them from the box.
2. Cut along the tape line at the top of the box.
3. Remove all parts from the top of the styrofoam and set aside.
4. Remove the styrofoam packing material from the top of the machine.
5. Carefully take out the machine components from the box and set aside.
6. Using the diagram below, ensure that all parts are present and in good
condition.
Pic. 4
Description
A. Motor
B. Remote controller
C. Dust chute
D. Canister shield (front and back)
E. Top upright supports (3)
F. Canister cover plate
G. Base frame
H. HEPA Canister filter
I. Canister shield (side)
J. Front and back drum panel
K. Side drum panel
L. Octagon drum lid
M. Cyclone funnel
N. Cyclone barrel
O. Intake cylinder
P. Octagon drum foot peddle
Q. Canister end cap with 4” port
R. Lower upright supports (3)
S. Vacuum suction ring
T. Upright support reinforcement plate (3)
U. Foot peddle bar (left and right)
V. Foot peddle assembly fittings
V1. Lower triangular support plate (2)
V2. Foot peddle bar support (2)
V3. Lower support plate (2)
W. Inlet adapter
X. Hardware box
Y. Operating and Parts Manual
Report any missing or damaged parts to your dealer or distributor. Prior to
tool assembly and use, read this manual thoroughly to familiarize yourself
with proper assembly, maintenance and safety procedures.
5.2 General Tool Assembly
This step requires two adults.
This 3HP Mobile Dust Cyclone is heavy,
be careful when lifting and handling it! Failure to comply may cause
serious injury and/or damage to the machine and/or property!
Tools Required
10 mm wrench / 12 mm wrench / 14 mm wrench
Phillips screwdriver. 4 mm hex wrench / 5 mm hex wrench
To assemble your dust cyclone, follow these steps:
For your own safety, do not connect the machine to the power source until
the machine is completely assembled. Please also make sure that you
read and understand the entire instruction manual.
ASSEMBLY TIME ESTIMATE 5-6 hours
Step 1: Turn the unit upside down. Make sure you use a cushion under
the canister top side to even out the unit to the same height as the motor.
Do not have the unit lopsided. Remove the base which has been fastened
to the (3) top upright supports.
Pic. 5
Step 2: Secure the (4) 3” wheels to the underside of the base (16)
5/16”*3/4” hex bolts and (16) 5/16”*od18*2T flat washers.
Pic. 6
Step 3: Turn the base around with it standing on the (4) 4” wheels and
secure the three lower upright support panels using (6) 3/8”*3/4” hex bolts
and (6) 3/8”*OD23*2t flat washers.
Each lower upright support panels numbered for its specific location.
A – shown with one dot is located on the canister side.
B – shown with two dots with extension on left is located on the front side
C – shown with two dots with extension on right is located on opposite end.
Pic. 7
Step 4: Install the foam tape to the upper and lower rims of the three
components listed, Cyclone funnel, Cyclone barrel, and Intake cylinder.
3HP Mobile Dust Cyclone Manual
13
UNPACKING
Your 3HP Mobile Dust Cyclone comes packed in a single box. Before attempting to
assemble this machine, follow these directions for unpacking:
1. Carefully cut the banding straps and remove them from the box.
2. Cut along the tape line at the top of the box.
3. Remove all parts from the top of the styrofoam and set aside.
4. Remove the styrofoam packing material from the top of the machine.
5. Carefully take out the machine components from the box and set aside.
6. Using the diagram below
,
ensure that all parts are present and in good condition.
DESCRIPTION (QUANTITY)
Figure 1
A. Motor
B. Remote controller
C. Dust chute
D. Canister shield (front and back)
E. Top upright supports (3)
F. Canister cover plate
G. Base frame
H. HEPA Canister filter
I. Canister shield (side)
J. Front and back drum panel
K. Side drum panel
L. Octagon drum lid
M. Cyclone funnel
N. Cyclone barrel
Report any missing or damaged parts to your dealer or distributor. Prior to tool
assembly and use, read this manual thoroughly to familiarize yourself with proper
assembly, maintenance and safety procedures.
G
J
K
M
N
L
P
Q
R
T
U
V
V
V1
V2
V3
Hardware
box
Manual
O. Intake cylinder
P. Octagon drum foot peddle
Q. Canister end cap with 4” port
R. Lower upright supports (3)
S. Vacuum suction ring
T. Upright support reinforcement plate (3)
U. Foot peddle bar (left and right)
V. Foot peddle assembly fittings
V1. Lower triangular support plate (2)
V2. Foot peddle bar support (2)
V3. Lower support plate (2)
W. Inlet adapter
X. Hardware box
Y. Operating and Parts Manual
X
Y
A
B
C
D
E
F
H
I
O
W
K
S
Manuál
Nářadí
3HP Mobile Dust Cyclone Manual
11
PROGRAMMING THE REMOTE CONTROL
1. Ensure the machine is switch ON before programming the remote control.
2. Press the BLACK set button on the bottom of the remote switch until you hear two beeps.
3. Press the Remote set button on your hand held controller simultaneously with the BLACK
button until you hear three beeps to complete the set up.
Receiver set button
Receiver set button
3HP Mobile Dust Cyclone Manual
15
Step Two: Secure the (4) 3” wheels to the underside of the base (16) 5/16”*3/4”
hex bolts and (16) 5/16”*od18*2T flat washers.
Step Three: Turn the base around with it standing on the (4) 4” wheels and
secure the three lower upright support panels using (6) 3/8”*3/4” hex bolts
and (6) 3/8”*OD23*2t flat washers.
Each lower upright support panels numbered for its specific location.
A – shown with one dot is located on the canister side.
B – shown with two dots with extension on left is located on the front side
C – shown with two dots with extension on right is located on opposite end.
A
C
B
A
B
C
