-13-
www.igmtools.com
Pic. 46
Step 43: Apply foam tape to the hole on the dust chute before securing
the pressure switch using (4) M4*12MM sheet metal thread bolts.
Pic. 47
Step 44: Locate the D1-1/4”*230mm black flex hose and two D1-1/4”
hose clamps in the hardware box. Connect the one end of the flex hose
to the vacuum suction tube which is located on the top end of the cyclone
cone. Connect the other end of the flex hose to the octagon drum lid
vacuum tube which is located on the back end of the drum lid closest to
the canister filter. Secure both ends with the hose clamps provided.
Pic. 48
Step 45: If you do not want to use a plastic bag inside the octagon
collection drum, you need to block off the negative pressure. There is a
little pack containing the items needed to do this. You will also need take
the (4) 1/4”*1/2” carriage bolts, (4) 1/4”*OD19*2t flat washers and (4) 1/4”
hex nuts that were securing the vacuum suction pipe to assemble the
cover plates. The vacuum suction pipe on the drum will be removed for
this. It will not have a purpose if you block off the negative pressure.
Pic. 49
Step 46: Remove the vacuum suction pipe from the drum by loosening the
(4) 1/4”*1/2” carriage bolts, (4) 1/4”*OD19*2t flat washers and (4) 1/4” hex
nuts mentioned in the previous step. There will be 2 sets from the top and
2 sets from the bottom of the vacuum suction pipe.
Pic. 50
Step 47: Take the one of the cover plates, (2) 1/4”*1/2” carriage bolts,
(2) 1/4”*OD19*2t flat washers and (2) 1/4” hex nuts and secure the cover
plate to the opening on the top of the drum. For the bottom holes do the
same, but first use foam tape to cover the square opening before bolting
on the cover plate.
Pic. 51
Step 48: Remove the flex hose and clamps from the cyclone cone in
step forty one. Locate the plug provided inside the hardware box and
attach over the vacuum suction tube as shown in the picture on the right
below.
3HP Mobile Dust Cyclone Manual
36
Step Forty Four: Locate the Ø1-1/4”*230mm black flex hose and two Ø1-1/4”
hose clamps in the hardware box. Connect the one end of the flex hose to the
vacuum suction tube which is located on the top end of the cyclone cone.
Connect the other end of the flex hose to the octagon drum lid vacuum tube
which is located on the back end of the drum lid closest to the canister filter.
Secure both ends with the hose clamps provided.
Step Forty Five: If you do not want to use a plastic bag inside the octagon
collection drum, you need to block off the negative pressure. There is a little pack
containing the items needed to do this. You will also need take the (4)
1/4”*1/2”
carriage bolts, (4) 1/4”*OD19*2t flat washers and (4) 1/4” hex nuts that were
securing the vacuum suction pipe to assemble the cover plates. The vacuum
suction pipe on the drum will be removed for this. It will not have a purpose if you
block off the negative pressure.
Cyclone Cone vacuum suction tube
Drum lid vacuum suction tube
Cover plates
Foam tape
Plug
3HP Mobile Dust Cyclone Manual
36
Step Forty Four: Locate the Ø1-1/4”*230mm black flex hose and two Ø1-1/4”
hose clamps in the hardware box. Connect the one end of the flex hose to the
vacuum suction tube which is located on the top end of the cyclone cone.
Connect the other end of the flex hose to the octagon drum lid vacuum tube
which is located on the back end of the drum lid closest to the canister filter.
Secure both ends with the hose clamps provided.
Step Forty Five: If you do not want to use a plastic bag inside the octagon
collection drum, you need to block off the negative pressure. There is a little pack
containing the items needed to do this. You will also need take the (4)
1/4”*1/2”
carriage bolts, (4) 1/4”*OD19*2t flat washers and (4) 1/4” hex nuts that were
securing the vacuum suction pipe to assemble the cover plates. The vacuum
suction pipe on the drum will be removed for this. It will not have a purpose if you
block off the negative pressure.
Cyclone Cone vacuum suction tube
Drum lid vacuum suction tube
Cover plates
Foam tape
Plug
Cover plates
Plug
Foam tape
3HP Mobile Dust Cyclone Manual
37
Step Forty Six: Remove the vacuum suction pipe from the drum by loosening the
(4)
1/4”*1/2” carriage bolts, (4) 1/4”*OD19*2t flat washers and (4) 1/4” hex nuts
mentioned in the previous step. There will be 2 sets from the top and 2 sets from
the bottom of the vacuum suction pipe.
Step Forty Seven: Take the one of the cover plates, (2)
1/4”*1/2” carriage bolts,
(2) 1/4”*OD19*2t flat washers and (2) 1/4” hex nuts and secure the cover plate to
the opening on the top of the drum. For the bottom holes do the same, but first
use foam tap
e to cover the square opening before bolting on the cover plate.
Cover plates
Cover plates
