IGM Laguna CFlux3Tv2, Руководство по эксплуатации

Страница: 11 / 18

-11- www.igmtools.com
Step 38: From the bottom of the canister filter, push the rotation shaft
through the hole in the middle of the canister cover plate.
Step 39: While holding the rotation shaft above the hole, insert the
bearing onto the shaft. This will fix the rotation shaft in place and you
will not need to keep holding it up. Secure the bearing using bolts (4) 6
mm*19 mm and washers (4) 6 mm*OD19*2T.
Step 40: Secure and tighten the (1) 8 mm*19 mm and (1) 8 mm*OD23*2T
flat washer on the rotation shaft base.
Step 41: Attach and secure the rotation crank to the top of the rotation
shaft using a hex bolt (1) 8 mm*19 mm and a flat washer (1) 8
mm*OD30*3T.
Step 42: All the assembly steps have been completed.
6. Maintenance procedures
CLEANING THE FILTER
To ensure proper operation of this Mobile Dust Cyclone, the HEPA
canister filter must have adequate air flow. This means the filter must
be regularly maintained by carefully blowing the filter clean using
compressed air and an air gun to release built-up particulates trapped
between the filter pleats.
For heavy duty users, it is recommended to use compressed air on a
regular basis to maintain maximum filtration efficiency and longer life span
of the filter.
Using the Filter Cleaner Crank
The filter cleaner crank knocks dust particulate and small debris from the
pleated filter and into the filter bag.
To keep your machine in good working condition, it is recommended that
you use the filter cleaner crank to clean the filter after every use.
To clean the filter using the crank simply rotate the crank handle clockwise
four or five rotations.
Using Compressed Air
Disconnect machine from power!
For heavy duty users, it is recommended to use compressed air on a
weekly basis to maintain maximum filtration efficiency and longer life span
of the filter.
REMOVING THE CANISTER FILTER
1. Follow the steps 29 to 34 in reverse to remove the canister filter.
2. With the canister filter removed use a compressed air gun to thoroughly
clean between the pleats, both inside and outside.
RE-ASSEMBLING THE CANISTER FILTER AFTER CLEANING
1. With the aid of another person, carefully re-insert the canister filter
repeating steps twenty nine to thirty four.
EMPTYING OR REPLACING THE FILTER BAG
Periodically check the filter bag, if it is more than one third full, it is
recommended that you empty it.
Pozn.: If the filter bag gets too full, the weight may force it to pull away
from the band clamp, exposing the user to potentially harmful particulates.
1. Release the spring-loaded band clamp at the bottom of the filter and
remove the filter bag.
2. Empty or replace the filter bag and re-attach using the spring-loaded
band clamp.
EMPTYING THE DRUM
Periodically inspect the contents of the drum and empty as needed. To
inspect the contents of the drum:
1. Raise the drum foot peddle bar to lower the drum to the floor.
2. Roll it away from the machine, inspect and empty as needed.
3HP Mobile Dust Cyclone Manual
32
Step Thirty Seven: Attach the canister cover plate to the dust chute using (12)
3/16”*1/2” sheet metal thread bolts.
Step Thirty Eight: From the bottom of the canister filter, push the rotation shaft
through the hole in the middle of the canister cover plate.
3HP Mobile Dust Cyclone Manual
33
Step Thirty Nine: While holding the rotation shaft above the hole, insert the
bearing onto the rotation shaft and pushing it down to the canister cover plate.
This will fix the rotation shaft in place and you will not need to keep holding it up.
Secure the bearing using (4) 1/4”*3/4” hex bolts and (4) 1/4”*OD19*2t flat
washers.
Step Forty: Secure and tighten the (1) 5/16”*3/4” and (1) 5/16”*OD23*2t flat
washer on the rotation shaft base.