IGBT Capio plus ILSCP24 Скачать руководство пользователя страница 46

Страница: 46 / 55

IGBT D

IMMER

ACKS

Installation

& Operation

Dimmer Status (continued)

Circuit

The circuit number of each dimmer in the system.

Description

The name of each dimmer set using Dimmer Setup.

Error

Any error reported by the dimmer from the list of possible errors. Errors are as follows:

ote

: Constant Circuit Modules will show the Error message "Not Present."

Load

The load in Watts (100 watt increments). If Snapshot is enabled, the variation from the sampled load will be displayed in parentheses.

Level

The current level of the dimmer in percentage and DMX512.

Temp

The current temperature of the dimmer in degrees Celsius.

Yellow - Temperature is approaching a dangerous level.

Red - Temperature is above a safe level and the dimmer has shutdown.

Status

The current status of the dimmer.

Line

The current Line Voltage at the system.

Mod Size

The size of this dimmer module in maximum wattage.

SW Ver

The version number of the dimmer firmware.

MESSAGE

MEANING

mis-wire

Dimmer power-up diagnostics sensed a line voltage greater than 185 VRMS.

watchdog

Dimmer firmware has been restarted after a software loop took too long to execute.

supply

The dimmer’s 18V power supply has dropped below 14 volts.

overtemp

Dimmer has exceeded safe temperature and has shut down.

overload

Dimmer has detected an overload (excessive current) due to a short circuit or a load that exceeds the dimmer’s rating.

igbt

An IGBT has failed.

rom

The read-only memory checksum is incorrect.

analog

Either the voltage or the current-sensing electronics has failed.

not present

The module slot is empty or contains a Constant Circuit Module.

Содержание Capio plus ILSCP24
























































Результаты поиска

Содержание Capio plus ILSCP24

Отзывы:

Похожие инструкции для Capio plus ILSCP24

Бренды по названию

Популярные бренды

IGBT Capio plus ILSCP24, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Capio plus ILSCP24

Отзывы:

Похожие инструкции для Capio plus ILSCP24

Бренды по названию

Популярные бренды