background image

8

5  Function

5.1  Measuring principle 

The sensor determines the level according to the capacitive measuring principle:
•  An electrical field [E] is generated 

and influenced by the medium to be 

detected. This change to the field 

causes a measurement signal that is 

electronically evaluated. 

•  The dielectric constant of a medium 

is important for its detection. Media 

with a high dielectric constant 

(e.g. water) generate a strong 

measurement signal, media with a 

low dielectric constant (e.g. oils) a 

correspondingly lower signal.  

•  The active measuring range of the 

sensor probe is composed of 16 

capacitive measuring segments. 

They generate measurement 

signals depending on the degree of 

coverage. 

Fig. 5-1

A

I

I

E

I: inactive zone

A: active zone (16 active segments)

E: electrical field

Dimensions → Technical data sheet

5.2  Operating principle / features of the unit

The unit can be installed in tanks of different sizes. 
2 outputs are available. They can be set separately.

OUT1

switching signal for level limit / IO-Link

OUT2

switching signal for level limit

To adjust to the present application select the required operating mode.

5.2.1  Operating modes
1.  Manual media selection with overflow prevention (factory setting LK10xx)

Recommended!

 

Highest operational reliability!

Содержание LK 022 Series






































Отзывы: