IFM LK 022 Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 37

IFM LK 022 Series Скачать руководство пользователя страница 21

21

UK

The unit can be configured before or after installation.

Exception: To adjust the overflow prevention [cOP], the unit

must

be instal-

led in the tank.

10.2 Basic settings

Setting ranges of all parameters:

Factory settings of all parameters:

10.2.1 Set unit of measurement [uni]

►

Enter [uni] before entering the values for SPx, rPx, OP or OFS.

This avoids unintentional wrong settings.

►

Select [uni].

►

Determine unit of measurement: [cm], [inch].

uni

10.2.2 Set offset [OFS]

The zone between tank bottom and lower edge of the measuring probe can be

entered as offset value

►

Set [OFS] before entering the values for SPx, rPx or OP.

This avoids unintentional wrong settings.

►

Select [OFS].

►

Set the value for the offset. Note the set unit of measurement [uni].

OFS

10.2.3 Set medium [MEdI]

►

Select [MEdI] and set the corresponding sensitivity:

MEdI

[CLW.1] = water, hydrous media, coolant emulsions
[CLW.2] = water, hydrous media, coolant emulsions for temperatures >

35 °C (installation in climatic tube)

[OIL.1] = oils with an increased dielectric constant (e.g. some synthetic

oils)

[OIL.2] = oils with a low dielectric constant (e.g. mineral oils)
[Auto] =

automatic medium detection

►

In case of doubt, select [OIL.2] for oils.

►

Check proper function by an application test!

«
...
19
20
21
22
23
...
»

Содержание LK 022 Series






































Отзывы:

Нет отзывов